KitchenAid 20.4 cu. ft. 36" Width Right-Hand Door Swing Dimensional Illustrations
36
"
Bottom Mount Built-in Refrigerator
®
PRODUCT MODEL NUMBERS
OVERALL DIMENSIONS
CABINET OPENING DIMENSIONS
DOOR SWING DIMENSIONS
KBLC36FM
KBLO36FM
KBLS36FM
KBLV36FP
KBLO36FM
KBLS36FM
KBLV36FP
KBRC36FM
KBRO36FM
KBRS36FM
KBRV36FP
KBRO36FM
KBRS36FM
KBRV36FP
Electrical:
A 115 Volt, 60 Hz., AC only 15- or
20- amp fused, grounded electrical supply is
required. It is recommended that a separate circuit
serving only your refrigerator be provided. Use an
outlet that cannot be turned off by a switch. Do not
use an extension cord.
required. It is recommended that a separate circuit
serving only your refrigerator be provided. Use an
outlet that cannot be turned off by a switch. Do not
use an extension cord.
A grounded 3 prong electrical outlet should be
placed within 4" (10.2 cm) of the right side cabi-
nets or end panel.
placed within 4" (10.2 cm) of the right side cabi-
nets or end panel.
Water Supply:
A cold water supply with water
pressure between 30 and 120 psi (207 - 827 kPa)
is required to operate the water dispenser and ice
maker. If you have questions about your water
pressure, call a licensed, qualified plumber.
is required to operate the water dispenser and ice
maker. If you have questions about your water
pressure, call a licensed, qualified plumber.
The water shutoff should be located in the base
cabinet on either side of the refrigerator or some
other easily accessible area. If the water shutoff
valve is not in the cabinets, the plumbing for the
water line can come through the floor or the back
wall.
cabinet on either side of the refrigerator or some
other easily accessible area. If the water shutoff
valve is not in the cabinets, the plumbing for the
water line can come through the floor or the back
wall.
IMPORTANT: The pressure of the water supply
coming out of a reverse osmosis system going to
the water inlet valve of the refrigerator needs to be
between 30 and 120 psi (207 - 827 kPa).
coming out of a reverse osmosis system going to
the water inlet valve of the refrigerator needs to be
between 30 and 120 psi (207 - 827 kPa).
If a reverse osmosis water filtration system is con-
nected to your cold water supply, the water pres-
sure to the reverse osmosis system needs to be a
minimum of 40 to 60 psi (276 - 414 kPa).
nected to your cold water supply, the water pres-
sure to the reverse osmosis system needs to be a
minimum of 40 to 60 psi (276 - 414 kPa).
Do not install the refridgerator near an oven, radia-
tor, or other heat source, or in a location where the
temperature will fall below 55°F (13°C).
tor, or other heat source, or in a location where the
temperature will fall below 55°F (13°C).
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Instructions packed with product. Specifications subject to change without notice.
Ref. 2317873
12-14-06
36
¹⁄₄
" (92 cm)
*83
³⁄₈
"
(211.8 cm)
80" - 90"
(203-229 cm)
4"
(10.2 cm)
6"
(15.2 cm)
24
"
(60.9 cm) min.
1"
(2.5 cm)
77"
(196 cm)
(196 cm)
6"
(15.2 cm)
6"
(15.2 cm)
83
1
/
2
" (212.1 cm) min.
84
3
/
4
" (215 cm) max.
to bottom of solid soffit
A
Width
35
1
/
2
" (90.2 cm) min.
35
3
/
4
" (90.8 cm) max
25
³⁄₈
"
(64.5 cm)
23
¹⁄₂
"
(59.7 cm)
84" (213 cm)
Power Cord
Power Cord
*83
³⁄₈
"
(211.8 cm)
*3
¹⁄₂
" (9 cm)
25
³⁄₈
"
(64.5 cm)
35
¹⁄₄
" (89.5 cm)
•
The water line attached to the back of the refrigerator is
5 ft (1.5 m) long.
•
Height dimensions are shown with leveling legs extended
¹⁄₈
" (3 mm) below the rollers.
* When leveling legs are fully extended to 1
¹⁄₄
" (32 mm) below
rollers, add 1
¹⁄₈
" (29 mm) to the height dimensions.
110˚
90˚
23"
(58 cm)
51"
(130 cm)
59"
(150 cm)
130˚
A solid soffit must be within 1" (2.5 cm)
maximum above the refrigerator. If the solid
soffit is higher than 1" (2.5 cm) or one is not
available, then the refrigerator must be
braced to prevent tipping during use.
maximum above the refrigerator. If the solid
soffit is higher than 1" (2.5 cm) or one is not
available, then the refrigerator must be
braced to prevent tipping during use.
If the anti-tip boards are needed, they must be
attached to the rear wall studs 80" to 90" (203
to 229 cm) above the floor.
attached to the rear wall studs 80" to 90" (203
to 229 cm) above the floor.
NOTE: A clearance of 1/2" (1.3 cm) must be
maintained in front of the refrigerator’s side
trim in order for the top grille to be removed.
maintained in front of the refrigerator’s side
trim in order for the top grille to be removed.
Top view
Front view
Side view