KitchenAid Hidden Controls ENERGY STAR® Qualified 5 Cycles & 4 Options Dimensional Illustrations
1/8 (3.2 mm)
1/8
(3.2 mm)
front
23-3/8
(59.4 cm)
Front View
Side
View
3/4
(1.9 cm)
*
25-29/32
(65.8 cm)
Drain hose and power supply line should enter through the
right side of opening in shaded areas.
Drain hose size: 1-1/2" (3.8 cm)
Power supply line hole-direct wired: 3/4" (1.9 cm)
Power supply line hole-with plug: 1-1/2" (3.8 cm)
right side of opening in shaded areas.
Drain hose size: 1-1/2" (3.8 cm)
Power supply line hole-direct wired: 3/4" (1.9 cm)
Power supply line hole-with plug: 1-1/2" (3.8 cm)
Water line should enter through the
left side of opening in shaded areas.
Minimum 1/2" (12,7 mm) hole.
left side of opening in shaded areas.
Minimum 1/2" (12,7 mm) hole.
Undercounter Dishwasher
®
PRODUCT MODEL SERIES
OVERALL DIMENSIONS
CABINET OPENING DIMENSIONS
CUSTOM FRONT PANEL DIMENSIONS
KUDC01TM
KUDI01DL
KUDI01FL
KUDI01IL
KUDL01IL
KUDP01DL
KUDI01DL
KUDI01FL
KUDI01IL
KUDL01IL
KUDP01DL
KUDP01FL
KUDP01IL
KUDS01DL
KUDS01FL
KUDS01IL
KUDS01VM
KUDP01IL
KUDS01DL
KUDS01FL
KUDS01IL
KUDS01VM
Electrical:
120-volt, 60 Hz, AC-only, 15 or
20 amp electrical supply. Use copper wire only. A
time-delay fuse or circuit breaker and separate
circuit is recommended.
time-delay fuse or circuit breaker and separate
circuit is recommended.
Water:
A hot water line with 20-120 psi
(138-862 kPa) water pressure. Water temperature
must be minimum 120°F (49°C) at dishwasher.
Use 3/8" O.D. copper tubing with compression
fitting or flexible stainless steel braided fill line
(1/2" minimum plastic tubing is optional but not
recommended). Use a 90° elbow with 3/8" N.P.T.
external pipe threads on one end to connect to
water inlet valve. Do not solder within 6" (15.2 cm)
from water inlet valve.
must be minimum 120°F (49°C) at dishwasher.
Use 3/8" O.D. copper tubing with compression
fitting or flexible stainless steel braided fill line
(1/2" minimum plastic tubing is optional but not
recommended). Use a 90° elbow with 3/8" N.P.T.
external pipe threads on one end to connect to
water inlet valve. Do not solder within 6" (15.2 cm)
from water inlet valve.
Drain:
Use the new drain hose supplied with your
dishwasher. If this is not suitable, use a new drain
hose with a maximum length of 12 feet (3.7 m)
that meets all current AHAM/IAPMO test
standards, is resistant to heat and detergent, and
fits the drain connector of the dishwasher. Must
have a high drain loop 20 inches (50.8 cm) above
the subfloor or floor. Connect drain hose to waste
tee or disposer inlet above drain trap in house
plumbing and 20 inches (50.8 cm) minimum
above the floor. An air gap must be used if the
drain hose is connected to house plumbing lower
than 20 inches (50.8 cm) above subfloor or floor.
Use 1/2" minimum I.D. drain line fittings.
hose with a maximum length of 12 feet (3.7 m)
that meets all current AHAM/IAPMO test
standards, is resistant to heat and detergent, and
fits the drain connector of the dishwasher. Must
have a high drain loop 20 inches (50.8 cm) above
the subfloor or floor. Connect drain hose to waste
tee or disposer inlet above drain trap in house
plumbing and 20 inches (50.8 cm) minimum
above the floor. An air gap must be used if the
drain hose is connected to house plumbing lower
than 20 inches (50.8 cm) above subfloor or floor.
Use 1/2" minimum I.D. drain line fittings.
Corner installation:
Allow 2" (5,1 cm)
minimum between corner wall and dishwasher
opening.
opening.
Grommet is required for electrical cable or power
supply cord hole cut in a metal cabinet.
supply cord hole cut in a metal cabinet.
Do not install dishwasher over carpeted floor.
Unit accepts custom door panels.
Top Vented Models
Front Vented Models
3/4" (1.9 cm) insulation –
may be compressed
(not used on all models)
may be compressed
(not used on all models)
23-7/8" (60.6 cm)
*For models using a 3/4"
(1.9 cm) custom wood front
panel, this dimension is
24-3/4" (62.9 cm).
panel, this dimension is
24-3/4" (62.9 cm).
24-1/2" (62.2 cm)*
21" (53.3 cm)
top vent
model
33-7/8"
(86 cm) min.
with wheels
removed
30-3/16" (76.7 cm)
3/4"
(19.1 mm)
23-1/2" (59.7 cm)
9"
(22.9 cm)
10"
(25.4 cm)
5-1/2"
(14 cm)
6" ***
(15.2 cm)
6" ***
(15.2 cm)
3-1/4"
(8.3 cm)
2-3/4"
(7 cm)
(7 cm)
34" (86.4 cm) min.
*
2"
(5.1 cm)
2"
(5.1 cm)
All surfaces must be free
from intrusions
2"
(5.1 cm)
3-1/4"
(8.3 cm)
3-1/4"
(8.3 cm)
2-3/4"
(7 cm)
(7 cm)
3-1/4"
(8.3 cm)
24" (61 cm)
min.
24" (61 cm)
**
*Measured from the lowest point on the underside of countertop.
May be reduced to 33-7/8" (86 cm) by removing wheels from dishwasher.
**Minimum, measured from narrowest point of opening.
***May be increased to 6-5/8" (16.6 cm) if height of opening is 34-1/2" (87.6 cm) at its lowest point.
Because Whirlpool Corporation policy includes a continuous commitment to improve our
products, we reserve the right to change materials and specifications without notice.
products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Instructions packed with product. Specifications subject to change without notice.
Ref. 8564554
10-04-04
24-7/8" (63.2 cm)
3/4" (1.9 cm) insulation –
may be compressed
(not used on all models)
may be compressed
(not used on all models)
24-1/2" (62.2 cm)*
front vent
model
21" (53.3 cm)
33-7/8"
(86 cm) min.
with wheels
removed
A custom front panel
must weigh no more
than 16 pounds and
must be made to these
dimensions.
must weigh no more
than 16 pounds and
must be made to these
dimensions.