Xerox DocuTech 6100 Production Publisher User Guide
Paper Trays & Loading Media
DT6180 HandyBook
24
Satisfaction Guide for 2-Sided Printing
Stock
Reliable feeds may be
expected
expected
Less reliable feeds may be
expected
expected
Suggested alternatives
Size
8 x 10 inches to 17 x 11
inches (203 x 254 mm to
432 x 279 mm)
inches (203 x 254 mm to
432 x 279 mm)
17 x 11 inch (432 x 279 mm)
paper can only be sent to
the top tray.
paper can only be sent to
the top tray.
Weight
Substance 16 to 110 (60 to
200 g/m2)
200 g/m2)
Substance 110 (200 g/m2)
must be long grain.
must be long grain.
Weights outside the limits
shown are not
recommended.
shown are not
recommended.
Type or
condition
condition
Xerographic bond paper in
good condition
good condition
Drilled stock, fanned
thoroughly
thoroughly
Slightly curled paper
Paper with reinforced edges
Do not use excessively
curled paper
curled paper
Refer to the “Using various
stocks” section for any stock
not defined in this guide.
stocks” section for any stock
not defined in this guide.
Satisfaction Guide for Various Stocks
Stock type
Instructions for use
• Recycled
Paper
Acceptable, but may increase paper dust
contamination problems in machine. Recommend
vacuum paper before installing in machine to
minimize paper dust.
contamination problems in machine. Recommend
vacuum paper before installing in machine to
minimize paper dust.
• Substance 13 (49 g/m2) paper
Use trays 3,4,or 5.
Do not run 2-sided prints.
Load the paper with seam side down into tray 3.
Optimum satisfaction can be expected with 8.5 x
11 inch (216 x 279 mm) or larger paper.
11 inch (216 x 279 mm) or larger paper.
• Substance 16 (60 g/m2) paper
Load paper with seam side up into trays 1 and 2;
seam side down into tray 3, 4, or 5.
seam side down into tray 3, 4, or 5.
Optimum satisfaction can be expected from tray
3, 4, or 5.
• Substance 20 (75 g/m2) paper
Load the paper with seam side up into trays 1
and 2; seam side down into trays 3, 4, and 5.
and 2; seam side down into trays 3, 4, and 5.
• Card
stock
• Xerox substance 65 (176 g/m2)
• Substance 110 (200 g/m2) long grain
(index)
Card stock can be run from any tray.
Reduce set size if frequent paper jams or
bindexer jams occur. If collated unfinished,
another solution is to lower the value of the
bindexer capacity set in the SWITCHES mode.
bindexer jams occur. If collated unfinished,
another solution is to lower the value of the
bindexer capacity set in the SWITCHES mode.
• Xerox 4024, substance 20 (75 g/m2)
• 3 hole drilled
• 4 hole drilled
• 7 hole drilled
Load the paper into trays 1 and 2 with holes to
the right; load the paper into trays 3, 4, and 5 with
holes to the left.
the right; load the paper into trays 3, 4, and 5 with
holes to the left.
Use the Image Shift or Reduce/Enlarge options
to avoid printing near the holes.
to avoid printing near the holes.
Fan the paper and check the paper for loose
paper plugs before loading the paper into the
trays.
paper plugs before loading the paper into the
trays.
• Never-tear, 3 hole drilled
Load the paper into trays 1 and 2 with holes to
the right; load the paper into trays 3, 4, and 5 with
the right; load the paper into trays 3, 4, and 5 with