Xerox DocuColor 12 Printer with Splash G630 Document
Customer Expectation Setting Document
Splash G630 for DocuColor 12
October 1, 2001
Terms and product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.
1
Customer Support
Server Installation
•
The physical installation of the Splash G630 server is done by a
Xerox Rigger / Carrier. Please call the Hotline number below if
the Xerox Rigger / Carrier did not perform the installation.
Xerox Rigger / Carrier. Please call the Hotline number below if
the Xerox Rigger / Carrier did not perform the installation.
•
Physical installation of the Splash Board solution is a customer
responsibility.
responsibility.
•
In all cases (System and Board) installation on the network is a
customer responsibility
customer responsibility
Software Upgrades
•
Periodically, Xerox will make available bug fixes and other
software releases. Future software releases will be designed to
be customer installable and it will be the customer’s responsibility
to perform the software upgrade activities.
software releases. Future software releases will be designed to
be customer installable and it will be the customer’s responsibility
to perform the software upgrade activities.
Hotline numbers
•
The Xerox Customer support Centers are available to provide
general information, answer questions, and take service calls.
You can reach the Customer Support Center at the following toll-
free phone numbers:
general information, answer questions, and take service calls.
You can reach the Customer Support Center at the following toll-
free phone numbers:
United States 1-800-821-2797
Canada 1-800-939-3769
Canada 1-800-939-3769
Analyst Services
•
A variety of services are available from your Xerox Systems
Analyst. All services are billable. Please contact your Sales
Representative for more information
Analyst. All services are billable. Please contact your Sales
Representative for more information
.
Customer Training
•
Customer Training is available on the Splash G630. All training is
billable. Please contact your Sales Representative for more
information.
billable. Please contact your Sales Representative for more
information.
Reference Material
The Splash G Series is shipped with the following G630
documentation:
documentation:
•
Splash G630 Color Server User Guide: This Guide is in PDF
format located on the User Software and User Documentation
CD-ROM bundled with the server.
format located on the User Software and User Documentation
CD-ROM bundled with the server.
•
Customer Release Notes: Contains customer information about
the server and client utility in hard copy format that was not
included in the electronic customer documentation. This
information includes caveats and workarounds and is available in
English, French, Italian, German, Spanish and Brazilian
Portuguese.
the server and client utility in hard copy format that was not
included in the electronic customer documentation. This
information includes caveats and workarounds and is available in
English, French, Italian, German, Spanish and Brazilian
Portuguese.
Space Requirements / Service Space Envelope
The following diagram is intended only as a representation of the
installation requirements of a fully configured DocuColor 12 with the
Splash G630.
installation requirements of a fully configured DocuColor 12 with the
Splash G630.
2” (48 m m )
24” (310 mm)
Minimum Space Requirements
For the Splash G630 Server
30” (720 mm)
36” (914 m m )
2” (48 m m )
24” (310 mm)
30” (720 mm)
Work Surface
or server
From left side
36” (914 m m )
Work Surface
or server
From left side
24” (310 mm)
DocuColor 12
Physical Information
Dimensions:
17.0” (H) x 8.9” (W) x 18.4” (D)
43.2cm (H) x 22.6 cm (W) x 46.7 cm (D)
Weight::
30 lbs. (13.6 kg)
RIP Power Cord
length
length
72" (1.8 meters)
Length of cable
connecting RIP to
DocuColor 12
connecting RIP to
DocuColor 12
240" (6 meters)
Electrical Requirements
Server
Voltage
115 / 220 VAC single phase,
manually configured
Amperage
15
Cycles (single phase)
60 Hz
Xerox Receptacle Part No.
600S3704
Receptacle NEMA Part
No.
No.
5-15R
Receptacle Diagram
Power
200 W maximum (excluding monitor)
50 W maximum for monitor
Note:
1. Surge protection is strongly recommended for all RIP
1. Surge protection is strongly recommended for all RIP
installations.
2. The power source for the RIP must be continuous and not
interrupted by an on-site power failure.
Installation Considerations
•
Electrical requirements and space requirements must be satisfied
prior to equipment delivery.
prior to equipment delivery.
•
A Xerox Rigger / Carrier physically installs the Splash G630. You
are responsible for configuring the RIP to the network.
are responsible for configuring the RIP to the network.
•
To enable System Administrators and others to work at the RIP,
the work surface should be desk height.
the work surface should be desk height.
•
To enable Xerox Service Representatives to safely repair the
system, the work surface should measure at least 45” x 30”.
system, the work surface should measure at least 45” x 30”.
•
The work surface of the RIP must not infringe on the space
required by the IOT and any attached accessories unless the
work surface is a table that has wheels and can be easily moved.
Refer to the DocuColor 12 Customer Expectation Setting
Document for dimensions.
required by the IOT and any attached accessories unless the
work surface is a table that has wheels and can be easily moved.
Refer to the DocuColor 12 Customer Expectation Setting
Document for dimensions.
•
There should be a minimum of 78 inches (1,981 mm) clearance
from the floor to the nearest overhead obstruction.
from the floor to the nearest overhead obstruction.
•
For printer installations with the Calibration Scanner an added
electrical outlet is needed.
electrical outlet is needed.
Environmental Requirements
Min.
Max.
Operating Temperature
50
o
F (10
o
C)
95
o
F (35
o
C)
Humidity (noncondensing)
5% RH
95% RH
Altitude (above sea level)
0
10,000 ft.
(3,048 m)
Voltage
90
132