Craftsman 3050 User Manual

...the light bulb blinks 3 times. 

Press any programmed PIN, then press and hold 
the 

*

 button until...

?  ?  ?  ?

PIN

?  ?  ?  ?

Temporary PIN

Enter the temporary 4-digit PIN of your 
choice, then press the ENTER button.   

The light bulb will blink 
4 times.  

Then press 
the     button.

Press the number 
of hours the 
temporary PIN 
will work (up to 255). 

Then press 
the # button.

Press the number 
of openings the 
temporary PIN 
will work (up to 255). 

1 blink

1 blink

To test, press the temporary 
PIN, then press the ENTER 
button. The garage door opener 
will activate. If the temporary
PIN was set for a number of 
openings, the test will use up 
one opening. 

To clear the temporary PIN, repeat steps 1-3 above, setting the number of hours or openings to 0 in step 3. 

*

Replace the battery when the keypad 
becomes dim or does not light after a 
button is pressed.

Dispose of old battery properly.

To prevent possible SERIOUS INJURY or DEATH:
•  NEVER allow small children near batteries.
•  If battery is swallowed, immediately notify doctor.

The garage door opener activates when the PIN and ENTER 
button are pressed. The keypad will blink for 15 seconds, during 
that time the ENTER button can be used to stop, start or reverse 
the door.

If the wrong number is accidentally pressed, press the correct 
PIN then the ENTER button. The Keyless Entry will transmit only 
the last four digits that were pressed before the ENTER button.

ONE BUTTON CLOSE: The Keyless Entry has a feature that allows 
the door to be closed using the ENTER button instead of a PIN.

  Press and hold the 1 and 9 buttons for 10 seconds. 

   The keypad will blink four times when the one button close 

feature is deactivated.

  Press and hold the 1 and 9 buttons for 10 seconds.

   The keypad will blink twice when the one button close feature 

is activated.

Battery  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  10A25

Keypad cover .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   41D621

Battery cover  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   41D541

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or 
modifications of this receiver and/or transmitter are prohibited, except for changing 
the code setting or replacing the battery. THERE ARE NO OTHER USER 
SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is 
subject to the following two conditions: (1) this device may not cause harmful 
interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation.

A temporary 4-digit PIN can be programmed to allow access 
to visitors. Each programmed PIN can program one temporary 
PIN. The temporary PIN can be set for a number of hours or a 
number of door openings. The temporary PIN cannot be the 
same as any previously programmed PIN.

   Select a location to mount the Keyless Entry at a minimum 

height of 5 feet (1.5 m) out of the reach of children.

  Remove battery cover and battery.

   Mark the top mounting hole and drill 1/8 inch (3.2 mm) 

pilot hole. 

   Install the top screw, allowing 1/8 inch (3.2 mm) to 

protrude above the surface. Position the Keyless Entry over 
the top screw.

   Mark the bottom hole and drill 1/8 inch (3.2 mm) pilot 

hole. Install the bottom screw. Do not overtighten to avoid 
cracking the plastic housing.

  Reinstall battery and replace cover. 

9V Battery