Zanussi ZHI611G Instruction Manual
11
GB
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Before connection to the mains supply
ensure that the mains voltage corresponds
to the voltage on the rating plate inside the
hood. Before carrying out any kind of
maintenance or cleaning, disconnect the
hood from the mains supply.
ensure that the mains voltage corresponds
to the voltage on the rating plate inside the
hood. Before carrying out any kind of
maintenance or cleaning, disconnect the
hood from the mains supply.
Fitting the decor panel
To fit the decor panel onto the hood will
require the removal of the complete facia
panel from the hood. Pull the panel out into
the operating position, press down on the
release catch located behind the door on the
left side of the casing to allow the facia panel
to be removed. The decor panel should be
fitted in accordance with the template
instructions using the 8 n. 3,9 x 13 mm dia.
screws supplied. Replace the facia panel
ensuring that it is seated correctly into the
two side guides. Act on the two V screws
placed inside the heads dor adjusting the
vapor shield sliding (see drawing n. 7).
require the removal of the complete facia
panel from the hood. Pull the panel out into
the operating position, press down on the
release catch located behind the door on the
left side of the casing to allow the facia panel
to be removed. The decor panel should be
fitted in accordance with the template
instructions using the 8 n. 3,9 x 13 mm dia.
screws supplied. Replace the facia panel
ensuring that it is seated correctly into the
two side guides. Act on the two V screws
placed inside the heads dor adjusting the
vapor shield sliding (see drawing n. 7).
Fixing side panels
To fit to the wooden side panels drill the side
panels in accordance with the template
instructions supplied. Remove the facia panel
and grille. Secure the hood to the side panels
with the 8 n. 3,5 x 16 mm dia. screws
supplied, through the holes in the sides of
the casing into the holes pre-drilled in the
wooden side panels (see drawing n. 8).
panels in accordance with the template
instructions supplied. Remove the facia panel
and grille. Secure the hood to the side panels
with the 8 n. 3,5 x 16 mm dia. screws
supplied, through the holes in the sides of
the casing into the holes pre-drilled in the
wooden side panels (see drawing n. 8).
Wall fitting
Use the paper template provided to mark the
hole position on the wall for the bracket fixing
screws. Two brackets and four screws with
rawl plugs are supplied. The brackets should
be fixed with the round end to the bottom.
Access to the wall levelling screws is from
above the hood. These are located in two
extension arms at either side of the hood
which fit over the wall brackets to support
the hood. By loosening the screws at the front
of each extension arm the hood can be
aligned at the correct distance from the wall
with the front of the adjoining wall cabinets.
By rotating the screw at the rear of each
extension arm clockwise the hood can be
lowered. Adjustement in an anti-clockwise
direction raises the hood, to ensure perfect
alignement with wall cabinets (see drawing
n. 9-10).
hole position on the wall for the bracket fixing
screws. Two brackets and four screws with
rawl plugs are supplied. The brackets should
be fixed with the round end to the bottom.
Access to the wall levelling screws is from
above the hood. These are located in two
extension arms at either side of the hood
which fit over the wall brackets to support
the hood. By loosening the screws at the front
of each extension arm the hood can be
aligned at the correct distance from the wall
with the front of the adjoining wall cabinets.
By rotating the screw at the rear of each
extension arm clockwise the hood can be
lowered. Adjustement in an anti-clockwise
direction raises the hood, to ensure perfect
alignement with wall cabinets (see drawing
n. 9-10).