Cisco Cisco Mobile Wireless Transport Manager 6.1 Release Notes
21
Release Notes for the Cisco Mobile Wireless Transport Manager 6.1.1
OL-20255-01
Open MWTM Caveats
Open MWTM Caveats
This section describes caveats that exist in the MWTM 6.1.1 software.
•
CSCsg92892
Symptom
When provisioning ITP nodes from the Provision tab of the web interface, some provisioning
operations might fail on the node with these symptoms and conditions:
Workaround
None. The user must know the ITP card information and specify correct values in the
provisioning request.
•
CSCsu02993
Provisioning Action
Symptom
Condition
Changing the media type for
FastEthernet or
GigabitEthernet interface
FastEthernet or
GigabitEthernet interface
Invalid input detected
FastEthernet or GigabitEthernet on the node does not support
the media type configuration option, but the user specified a
media type in the MWTM provisioning request.
the media type configuration option, but the user specified a
media type in the MWTM provisioning request.
Changing speed for
FastEthernet or
GigabitEthernet interface
FastEthernet or
GigabitEthernet interface
Invalid input detected
FastEthernet or GigabitEthernet on the node does not support
the speed configuration option, but the user specified the speed
in the MWTM provisioning request.
the speed configuration option, but the user specified the speed
in the MWTM provisioning request.
Configuring MTP3 User
Adaptation (M3UA) or
SCCP User Adaptation
(SUA) offload, or Local Peer
offload
Adaptation (M3UA) or
SCCP User Adaptation
(SUA) offload, or Local Peer
offload
Error: at least one
address must reside on
slot xx
The user specified an IP address that does not exist for the
specified card slot.
specified card slot.
Configuring M3UA or SUA
offload, or Local Peer
offload
offload, or Local Peer
offload
Error: XXX is already
offloaded to this
linecard slot=xx
The user specified a target card slot that is already in use by
another M3UA or SUA offload, or Local Peer offload.
another M3UA or SUA offload, or Local Peer offload.
Note
The ITP does not allow mixed types between M3UA or
SUA offload, and Local Peer offload.
SUA offload, and Local Peer offload.
Configuring the line priority
for the clock source line
option on the Cisco 2600
T1/E1 controller
for the clock source line
option on the Cisco 2600
T1/E1 controller
% Invalid input detected
at '^' marker.
The '^' marker points to the
line priority: primary or
secondary.
line priority: primary or
secondary.
While configuring the clock source line priority option on the
T1/E1 controller, the user specified the primary or secondary
option on the line, but the WAN Interface Card (WIC) card has
only one port, and does not support the line priority option.
T1/E1 controller, the user specified the primary or secondary
option on the line, but the WAN Interface Card (WIC) card has
only one port, and does not support the line priority option.
Configuring the secondary
line priority for the clock
source line option on the
Cisco 7xxx ITP T1/E1
controller
line priority for the clock
source line option on the
Cisco 7xxx ITP T1/E1
controller
% Invalid input detected
at '^' marker.
The '^' marker points to the
secondary line priority:
primary or secondary.
secondary line priority:
primary or secondary.
When configuring the clock source secondary line priority
option on the T1/E1 controller, the user specified a number that
is greater than the supported range on the device. Although the
MWTM allows values 1-72, some cards only support 1-8 or
1-16.
option on the T1/E1 controller, the user specified a number that
is greater than the supported range on the device. Although the
MWTM allows values 1-72, some cards only support 1-8 or
1-16.