Fujifilm Polyplast PYEL (Rigid) Product Datasheet
Polyplast PY EL Systems
Product Information
Finish
High Gloss
Drying
Jet drying: 55-65°C, 15-25 seconds. Overprints may require longer.
Air drying 20-30 minutes.
Thinning
Ink and Varnish: 15-25% ZV557 Standard Thinner
Hot shop conditions: 15-25% ZV558 Retarder
High speed Printing: 15-25% ZV556 Fast Thinner
Wash-Up
Xtend ZT639 Screen Wash Universal. Actisol Surperjet Spray.
Mesh
No. 90 monofilament or coarser.
Stencil Type
Any recommended solvent resistant Dirasol emulsion, Capillex film
or Indirect stencil.
Coverage & Mesh
45-55 m
2
/kg. 90 monofilament
Application
Acrylic, Polycarbonate and other Rigid Plastics.
Colour Range
13 Shades including Seritone Matching System.
Properties
Up to 5 years outdoor life in Zone 1
Safe, low temperature, jet drying.
Good flexibility and product resistance.
Excellent screen stability and self-solvency.
Product Resistance
Polyplast PY EL inks and PY383 EL Overvarnish have good
resistance to a variety of products including Petrol, Alcohol and
Battery Acid. If wider Chemical Resistance is required the use of
APR VA401 Varnish can be used, however the outdoor exposure
will be less than 2 years.
IMPORTANT
Stir well before every use. Always test application fully before
beginning a production run, as there are often considerable
variances in plastics from different manufacturers and even
between different batches.
Light Resistant Screen Ink for Rigid Plastic Signs
Main Characteristics
Polyplast PY EL is a system of inks designed for long life outdoor
applications on suitable Rigid Plastics for signs.
Special Recommendation
To obtain best results from the Polyplast PY EL Systems, the following
recommendations must be followed during colour matching and
print production.
1. The 13 colours, which comprise the EL System and Polyplast PY383
Varnish, may be:
Printed over and under each other. Intermixed for matching purposes
Printed over and under each other. Intermixed for matching purposes
provided that:
The combined proportion by weight of PY021 White, PY030
The combined proportion by weight of PY021 White, PY030
Tinting White and PY383 Varnish does not exceed 80% of the total
colour match mix. The individual proportion of any one colour,
except Black is not below 5% of the total mix.
2. Universal Tinters must not be added to PY EL colour matches.
3. Only colours in the PYEL system should be used.
4. The EL System must be printed on to suitably durable and
2. Universal Tinters must not be added to PY EL colour matches.
3. Only colours in the PYEL system should be used.
4. The EL System must be printed on to suitably durable and
compatible substrates.
5. Because of different pigmentation, the PY EL colours may vary in
5. Because of different pigmentation, the PY EL colours may vary in
shade from the same named colours in the standard Polyplast PY
range.
6. Finishing process, which includes heating, may adversely affect
6. Finishing process, which includes heating, may adversely affect
colour. Please check prior to production.
7. Prints on acrylic signs should not be over varnished with PY433.
7. Prints on acrylic signs should not be over varnished with PY433.
PY383 is recommended where a varnish is required.
Please Note
Many Plastics may have trace amounts of plasticiser or other
contaminants on the surface that may impair adhesion and block
resistance, even a considerable period after printing.
These contaminants can be removed from the surface with White or
Methylated Spirit or similar cleaning solvent before printing.
Plastics can become brittle when printed, possibly to the point of
shattering, often after several weeks. It is therefore essential to
check compatibility between ink/varnish and Plastic.
Outdoor-Use
Weathering tests have been carried out on prints produced in zone 1
with Polyplast PY EL (Unvarnished), which indicate 5 years outdoor
exposure in the UK or similar climate before significant colour change
was evident.
PY EL prints can be over-varnished with PY383 Overprint Varnish.
This will enhance colour and gloss retention but does not
extend outdoor durability. Users should always check with their
substrate supplier to ensure a suitable long life material is used.
Outdoor Use - APR Varnish
Polyplast PY EL inks have good resistance to a wide range of solvents
including petrol and alcohol, however where exceptionally high
resistance to petrol is required, overprinting with VA401 APR varnish
is recommended. PY EL prints over varnished with VA401 are not
suitable for outdoor use in excess of 2 years.
SERICOL