Cisco Cisco Gigabit Ethernet Switch Module (CGESM) for HP Technical References
2-170
Cisco Gigabit Ethernet Switch Module for the HP p-Class BladeSystem Command Reference Guide
380265-002
Chapter 2 CGESM Switch Cisco IOS Commands
match (class-map configuration)
match (class-map configuration)
Use the match class-map configuration command to define the match criteria to classify traffic. Use the
no form of this command to remove the match criteria.
no form of this command to remove the match criteria.
match {access-group acl-index-or-name | input-interface interface-id-list | ip dscp dscp-list | ip
precedence ip-precedence-list}
no match {access-group acl-index-or-name | input-interface interface-id-list | ip dscp dscp-list |
ip precedence ip-precedence-list}
Syntax Description
Defaults
No match criteria are defined.
Command Modes
Class-map configuration
Command History
Usage Guidelines
The match command is used to specify which fields in the incoming packets are examined to classify
the packets. Only the IP access group or the MAC access group matching to the Ether Type/Len are
supported.
the packets. Only the IP access group or the MAC access group matching to the Ether Type/Len are
supported.
To define packet classification on a physical-port basis, only one match command per class map is
supported. In this situation, the match-all and match-any keywords are equivalent.
supported. In this situation, the match-all and match-any keywords are equivalent.
For the match ip dscp dscp-list or the match ip precedence ip-precedence-list command, you can enter
a mnemonic name for a commonly used value. For example, you can enter the match ip dscp af11
command, which is the same as entering the match ip dscp 10 command. You can enter the match ip
a mnemonic name for a commonly used value. For example, you can enter the match ip dscp af11
command, which is the same as entering the match ip dscp 10 command. You can enter the match ip
access-group
acl-index-or-name
acl-index-or-name
Number or name of an IP standard or extended access control list (ACL) or
MAC ACL. For an IP standard ACL, the ACL index range is 1 to 99 and 1300
to 1999. For an IP extended ACL, the ACL index range is 100 to 199
and 2000 to 2699.
MAC ACL. For an IP standard ACL, the ACL index range is 1 to 99 and 1300
to 1999. For an IP extended ACL, the ACL index range is 100 to 199
and 2000 to 2699.
input-interface
interface-id-list
interface-id-list
Specify the physical ports to which the interface-level class map in a
hierarchical policy map applies. You can specify up to six entries in the list
by specifying a port (counts as one entry), a list of ports separated by a space
(each port counts as an entry), or a range of ports separated by a hyphen
(counts as two entries).
hierarchical policy map applies. You can specify up to six entries in the list
by specifying a port (counts as one entry), a list of ports separated by a space
(each port counts as an entry), or a range of ports separated by a hyphen
(counts as two entries).
ip dscp dscp-list
List of up to eight IP Differentiated Services Code Point (DSCP) values to
match against incoming packets. Separate each value with a space. The range
is 0 to 63. You also can enter a mnemonic name for a commonly-used value.
match against incoming packets. Separate each value with a space. The range
is 0 to 63. You also can enter a mnemonic name for a commonly-used value.
ip precedence
ip-precedence-list
ip-precedence-list
List of up to eight IP-precedence values to match against incoming packets.
Separate each value with a space. The range is 0 to 7. You also can enter a
mnemonic name for a commonly-used value
Separate each value with a space. The range is 0 to 7. You also can enter a
mnemonic name for a commonly-used value
Release
Modification
12.2(25)SE1
This command was introduced.