Intel L7700 LE80537LG0334M User Manual
Product codes
LE80537LG0334M
Datasheet
75
Package Mechanical Specifications and Pin Information
DBR#
Output
DBR# (Data Bus Reset) is used only in processor systems where no
debug port is implemented on the system board. DBR# is used by
a debug port interposer so that an in-target probe can drive system
reset. If a debug port is implemented in the system, DBR# is a no
connect in the system. DBR# is not a processor signal.
debug port is implemented on the system board. DBR# is used by
a debug port interposer so that an in-target probe can drive system
reset. If a debug port is implemented in the system, DBR# is a no
connect in the system. DBR# is not a processor signal.
DBSY#
Input/
Output
DBSY# (Data Bus Busy) is asserted by the agent responsible for
driving data on the FSB to indicate that the data bus is in use. The
data bus is released after DBSY# is deasserted. This signal must
connect the appropriate pins on both FSB agents.
driving data on the FSB to indicate that the data bus is in use. The
data bus is released after DBSY# is deasserted. This signal must
connect the appropriate pins on both FSB agents.
DEFER#
Input
DEFER# is asserted by an agent to indicate that a transaction
cannot be guaranteed in-order completion. Assertion of DEFER# is
normally the responsibility of the addressed memory or Input/
Output agent. This signal must connect the appropriate pins of
both FSB agents.
cannot be guaranteed in-order completion. Assertion of DEFER# is
normally the responsibility of the addressed memory or Input/
Output agent. This signal must connect the appropriate pins of
both FSB agents.
DINV[3:0]#
Input/
Output
DINV[3:0]# (Data Bus Inversion) are source synchronous and
indicate the polarity of the D[63:0]# signals. The DINV[3:0]#
signals are activated when the data on the data bus is inverted.
The bus agent will invert the data bus signals if more than half the
bits, within the covered group, would change level in the next
cycle.
indicate the polarity of the D[63:0]# signals. The DINV[3:0]#
signals are activated when the data on the data bus is inverted.
The bus agent will invert the data bus signals if more than half the
bits, within the covered group, would change level in the next
cycle.
DPRSTP#
Input
DPRSTP# when asserted on the platform causes the processor to
transition from the Deep Sleep State to the Deeper Sleep state. In
order to return to the Deep Sleep State, DPRSTP# must be
deasserted. DPRSTP# is driven by the ICH7M chipset.
transition from the Deep Sleep State to the Deeper Sleep state. In
order to return to the Deep Sleep State, DPRSTP# must be
deasserted. DPRSTP# is driven by the ICH7M chipset.
DPSLP#
Input
DPSLP# when asserted on the platform causes the processor to
transition from the Sleep State to the Deep Sleep state. In order to
return to the Sleep State, DPSLP# must be deasserted. DPSLP# is
driven by the ICH7M chipset.
transition from the Sleep State to the Deep Sleep state. In order to
return to the Sleep State, DPSLP# must be deasserted. DPSLP# is
driven by the ICH7M chipset.
DPWR#
Input
DPWR# is a control signal from the Intel® 945GM/GT/GMS/PM and
940GML Express Chipset family used to reduce power on the
processor data bus input buffers.
940GML Express Chipset family used to reduce power on the
processor data bus input buffers.
DRDY#
Input/
Output
DRDY# (Data Ready) is asserted by the data driver on each data
transfer, indicating valid data on the data bus. In a multi-common
clock data transfer, DRDY# may be deasserted to insert idle clocks.
This signal must connect the appropriate pins of both FSB agents.
transfer, indicating valid data on the data bus. In a multi-common
clock data transfer, DRDY# may be deasserted to insert idle clocks.
This signal must connect the appropriate pins of both FSB agents.
Table 16.
Signal Description (Sheet 3 of 8)
Name
Type
Description
DINV[3:0]# Assignment To Data Bus
Bus Signal
Data Bus
Signals
DINV[3]#
D[63:48]#
DINV[2]#
D[47:32]#
DINV[1]#
D[31:16]#
DINV[0]#
D[15:0]#