Cisco Cisco Firepower Management Center 4000 Installation Guide
5-2
Cisco NGIPS for Blue Coat X-Series Installation and Configuration Guide
Chapter 5 Managing Cisco NGIPS for Blue Coat X-Series
Editing Load-Balanced VAP Groups
where
vap_group_name
is the name of the VAP group and
vap_1
is the first VAP in the VAP group, and
vap_2
is the second VAP in the same VAP group, separated by a space. For example, to restrict load
balancing to the existing two VAPs on the
ABC
VAP group, enter the following commands separately and
in sequence:
CBS# configure vap
-
group ABC
CBS(config-vap-grp)# available-vap-list 1 2
Step 2
Increase the
vap-count
and the
max-load-count
by entering the following commands separately and in
sequence:
CBS(config
-
vap
-
grp)# vap
-
count vap-count-quantity
CBS(config
-
vap
-
grp)# max
-
load
-
count max-load-quantity
CBS(config
-
vap
-
grp)# end
where
vap-count-quantity
is the total number of VAPs you want in the VAP group and
max-load-quantity
is the maximum number of VAPs you want in the VAP group. For example, if you
have two VAPs in the
ABC
load-balanced group and want to add two new VAPs, you can increase the
vap-count
and the
max-load-count
to
4
by entering the following commands separately and in
sequence:
CBS(config
-
vap
-
grp)# vap
-
count 4
CBS(config
-
vapvgrp)# max
-
load
-
count 4
CBS(config
-
vap
-
grp)# end
Step 3
After the new VAPs boot, use the
application-update
command to install Cisco NGIPS for Blue Coat
X-Series:
application
-
update vap
-
group vap_group_name
where
vap_group_name
is the name of the VAP group. For example, you can update the VAP group named
ABC
by entering the following command:
application
-
update vap
-
group ABC
Step 4
Provide the management interface, sensing interfaces, and management host IP address for the new
VAPs.
VAPs.
Step 5
Reload the new VAPs in the VAP group by entering the following command:
CBS# reload vap
-
group vap_group_name vap_3 vap_4
where
v
ap_group_name
is the name of the VAP group, and
vap_3
and
vap_4
are the number that identify
the two new VAPs. For example, add the two new VAPs to the VAP group named
ABC
by entering the
following command:
CBS# reload vap
-
group ABC 3 4
Step 6
Register Cisco NGIPS for Blue Coat X-Series with the Defense Center and create interfaces. For more
information, see
information, see
Step 7
Push the appropriate policies to the new VAPs using the user interface on the Defense Center that
manages the device. See the FireSIGHT System User Guide for more information.
manages the device. See the FireSIGHT System User Guide for more information.
Step 8
Set the
available-vap-list
back to include all VAPs by entering the following command:
CBS# configure vap
-
group vap_group_name
available-vap-
list vap_1 vap_2 vap_3 vap_3
where
vap_group_name
is the name of the VAP group and
vap_1
,
vap_2
,
vap_3
and
vap_4
are the
numbers that identify the VAPs. For example:
CBS# configure vap-group ABC
available-vap-list 1 2 3 4
Editing Load-Balanced VAP Groups
You may want to add or remove a VAP from a load-balanced VAP group.