Cisco Cisco ASA 5580 Adaptive Security Appliance Leaflet
4-134
思科 ASA 系列命令参考，S 命令
第 4 章 show bgp 至 show cpu 命令
show controller
示例
以下是
show controller 命令的输出示例：
ciscoasa# show controller
Ethernet0/0:
Marvell 88E6095 revision 2, switch port 7
PHY Register:
Control: 0x3000 Status: 0x786d
Identifier1: 0x0141 Identifier2: 0x0c85
Auto Neg: 0x01e1 LP Ability: 0x40a1
Auto Neg Ex: 0x0005 PHY Spec Ctrl: 0x0130
PHY Status: 0x4c00 PHY Intr En: 0x0400
Int Port Sum: 0x0000 Rcv Err Cnt: 0x0000
Led select: 0x1a34
Reg 29: 0x0003 Reg 30: 0x0000
Port Registers:
Status: 0x0907 PCS Ctrl: 0x0003
Identifier: 0x0952 Port Ctrl: 0x0074
Port Ctrl-1: 0x0000 Vlan Map: 0x077f
VID and PRI: 0x0001 Port Ctrl-2: 0x0cc8
Rate Ctrl: 0x0000 Rate Ctrl-2: 0x3000
Port Asc Vt: 0x0080
In Discard Lo: 0x0000 In Discard Hi: 0x0000
In Filtered: 0x0000 Out Filtered: 0x0000
Global Registers:
Control: 0x0482
---------------------------------------------------------------------
Number of VLANs: 1
---------------------------------------------------------------------
Vlan[db]\Port| 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 |
---------------------------------------------------------------------
<0001[01]> | EUT| EUT| EUT| EUT| EUT| EUT| EUT| EUT| EUM| NM | NM |
---------------------------------------------------------------------
....
Ethernet0/6:
Marvell 88E6095 revision 2, switch port 1
PHY Register:
Control: 0x3000 Status: 0x7849
Identifier1: 0x0141 Identifier2: 0x0c85
Auto Neg: 0x01e1 LP Ability: 0x0000
Auto Neg Ex: 0x0004 PHY Spec Ctrl: 0x8130
PHY Status: 0x0040 PHY Intr En: 0x8400
Int Port Sum: 0x0000 Rcv Err Cnt: 0x0000
Led select: 0x1a34
Reg 29: 0x0003 Reg 30: 0x0000
Port Registers:
Status: 0x0007 PCS Ctrl: 0x0003
Identifier: 0x0952 Port Ctrl: 0x0077
Port Ctrl-1: 0x0000 Vlan Map: 0x07fd
VID and PRI: 0x0001 Port Ctrl-2: 0x0cc8
Rate Ctrl: 0x0000 Rate Ctrl-2: 0x3000
Port Asc Vt: 0x0002
In Discard Lo: 0x0000 In Discard Hi: 0x0000
In Filtered: 0x0000 Out Filtered: 0x0000
----Inline power related counters and registers----
Power on fault: 0 Power off fault: 0
Detect enable fault: 0 Detect disable fault: 0
Faults: 0
Driver counters:
I2C Read Fail: 0 I2C Write Fail: 0