Cisco Cisco Nexus 9000v Switch Release Notes
Cisco Nexus 9000 Series NX-OS Release Notes, Release 7.0(3)I2(4)
Caveats
15
Record Number
Description
Show tech dme or dme logs will indicate following log messages on active sup as well as standby.
[aaa] [DBG4] [] Failed to send ICMP Request (101) for sys/userext/tacacsext/tacacsplusprovider-x.x.x.x
Where x.x.x.x is the ip address of the tacacs or radius server.
An N3K running nxos.7.0 has an IPv6 BGP session to a directly connected peer on a port-channel sub-
interface. The peer addresses are link local addresses. The port-channel sub-interfaces have the same
IPv6 link local address configured. If the link local address on an unrelated interface is changed a TCP
reset gets sent for the IPv6 BGP session. Shut/no shut on the BGP interface is needed to recover.
interface. The peer addresses are link local addresses. The port-channel sub-interfaces have the same
IPv6 link local address configured. If the link local address on an unrelated interface is changed a TCP
reset gets sent for the IPv6 BGP session. Shut/no shut on the BGP interface is needed to recover.
N9500 is a Border Leaf and learns prefix 172.21.26.0/24 via BGP in vrf from a firewall outside the
fabric, and learns a default route from EVPN fabric in the same vrf from another Border Leaf.
fabric, and learns a default route from EVPN fabric in the same vrf from another Border Leaf.
N0-DC1L-BLV-ZF-SV100# bcm-shell module 1 "l3 defip show" | grep 0.0.0.0
2304 3 0.0.0.0/0 00:00:00:00:00:00 100018 0 0 0 0 n <<<
3072 Global 0.0.0.0/0 00:00:00:00:00:00 149149 0 0 0 0 y
2304 3 0.0.0.0/0 00:00:00:00:00:00 100018 0 0 0 0 n <<<
3072 Global 0.0.0.0/0 00:00:00:00:00:00 149149 0 0 0 0 y
When 9500 received packet from L3Vni destined to 172.21.26.0/24, it incorrectly forwards the packet
using the default route programmed in VRF, instead of sending it to the fabric module that causes the
packet to go into a loop.
using the default route programmed in VRF, instead of sending it to the fabric module that causes the
packet to go into a loop.
By default, the VSH daemon has console and vty exec-timeout turned off.
The objects of type macAddress are shown as long ascii strings, instead of 6 byte hexa decimal values
of the MAC address.
of the MAC address.
LC would reset due to sysmgr resetting vntagc due to missing hearbeats. The following errors could
appear in show logging nvram:
appear in show logging nvram:
VDC-1 %$ %SYSMGR-SLOT7-2-SERVICE_CRASHED: Service "vntagc" (PID 2816) hasn't caught signal 6
(core will be saved).
(core will be saved).
VDC-1 %$ %MODULE-2-MOD_DIAG_FAIL: Module 7 reported failure due to Service on linecard had a
hap-reset in device DEV_SYSMGR (device error 0x402)
hap-reset in device DEV_SYSMGR (device error 0x402)
VDC-1 %$ %PLATFORM-2-MOD_DETECT: Module 7 detected Module-Type 48x1/10G SFP+ 4x40G
Ethernet Module Model N9K-X9564PX
Ethernet Module Model N9K-X9564PX
VDC-1 %$ %PLATFORM-2-MOD_PWRUP: Module 7 powered up
Change HA policy of vntagc from reset to statuful. The vntagc crashes and related modules reset
which cause route reconvergence again and packet loss.
which cause route reconvergence again and packet loss.