Cisco Cisco ONS 15454 M2 Multiservice Transport Platform (MSTP)

This step does not apply to passive units that are to be installed within the passive
shelf.

Note

To add a passive DCU, you need to choose a slot number from the Slot Number Selection dialog box and click
OK.

Note

Step 4

To add a MF-6RU unit, in the multishelf view right-click the gray space inside the rack and choose Add Shelf > PASSIVE
SHELF MF. The Shelf ID Section dialog is displayed.

Step 5

Choose a shelf ID and click OK. The MF-6RU unit is added to the rack.

Step 6

To add a MF10-6RU unit, in the multishelf view right-click the gray space inside the rack and choose Add Shelf >
PASSIVE SHELF MF10.The Shelf ID Section dialog is displayed.

Step 7

Choose a shelf ID and click OK. The MF10-6RU unit is added to the rack.

Step 8

To add a passive unit to the MF-6RU or MF10-6RU shelf, double-click the shelf to open shelf mode or right-click the
passive shelf and choose Open Shelf.

Step 9

Right-click a slot inside the passive shelf and choose Add Card > WDM > PASSIVE > passive unit
The MF-2MPO-ADP, MF-4X4-COFS, MF-DEG-5, MF-MPO-8LC, MF-6AD-CFS, and MF-UPG-4 passive units can be
provisioned in the MF-6RU passive shelf.

The MF-10AD-CFS, MF-16AD-CFS, MF-16AE-CFS, MF-MPO-16LC, MF-8X10G-FO, and MF-MPO-20LC passive
units can be provisioned in the MF10-6RU passive shelf.

Step 10

To add a shelf, in the multishelf view right-click the gray space inside the rack and choose Add Shelf >
CHASSIS_454SDH(ETSI) or CHASSIS_454(ANSI) or 15454 M6 ANSI or 15454 M6 ETSI.

Step 11

In the Shelf ID Selection dialog box, choose a shelf ID from the drop-down list.

Step 12

Click OK. The shelf appears in the multishelf view.

Step 13

Complete the "DLP-G46 Log into CTC" task in the "

Connect the PC and Log into the GUI

" document at the new shelf

that has to be configured as a subtending shelf.

Step 14

In multishelf view, click the Provisioning > General > Multishelf Config tabs.

Step 15

Click Enable as Subtended Shelf.

Step 16

From the Shelf ID drop-down list, choose the shelf ID that you created in

Step 11, on page 15

Step 17

Click Apply.

Step 18

In the confirmation dialog box, click Yes to reboot the shelf. The CTC view changes to network view and the node icon
changes to gray. (This might take several minutes.)

Step 19

If you are connecting the new ONS 15454 subtending shelf to the Ethernet Adapter Panel (EAP), complete the following
steps. If not, continue with

Step 22, on page 16

a) Using a cross-over (CAT 5) LAN cable, plug one connector into the RJ-45 front panel port of the subtending shelf

TCC2/TCC2P/TCC3 card in Slot 7 and plug the other end into the SSC port on the left patch panel.

b) Using a cross-over (CAT 5) LAN cable, plug one connector into the RJ-45 front panel port of the subtending shelf

TCC2/TCC2P/TCC3 card in Slot 11 and plug the other end into the SSC port on the right patch panel.

Step 20

If you are connecting the ONS 15454 subtending shelf to the Catalyst 2950 or the Catalyst 3560 switch, complete the
following steps. If not, continue with

Step 22, on page 16

a) Plug one end of a cross-over (CAT-5) LAN cable into the RJ-45 front panel port of the subtending shelf

TCC2/TCC2P/TCC3 card in Slot 7 and plug the other end into Port 2 of the active Catalyst 2950 or Catalyst 3560.

b) Plug one end of a cross-over (CAT-5) LAN cable into the RJ-45 front panel port of the subtending shelf

TCC2/TCC2P/TCC3 card in Slot 11 and plug the other end into Port 2 of the standby Catalyst 2950 or Catalyst 3560.

Step 21

To connect an ONS 15454 M6 subtending shelf to the Catalyst 3560 switches, complete the following: