Cisco Cisco ONS 15454 M2 Multiservice Transport Platform (MSTP)
For additional information, including valid command values, refer to the Cisco ONS SONET TL1 Command Guide or the
Cisco ONS SDH TL1 Command Guide .
Cisco ONS SDH TL1 Command Guide .
Step 11
In the TL1 dialog box, use the DLT-OCHCC command to delete the OCHCC cross-connects for the express path OCHCCs
listed in
listed in
Step 4, on page 20
, using the following format:
DLT-OCHCC:[<TID>]:<AID>:<CTAG>[:::CKTID=<CKTID>],[CMDMDE=<CMDMDE>];
where:
where:
• <AID> is the access identifier from the Facility section.
• <CKTID> is the cross-connect ID. The default is Blank or None. CKTD is a string of ASCII characters. The maximum
length is 48. If CKTID is empty or null, the CKTID field will not be displayed.
• <CMDMDE> is the command execution mode. NORM mode is the default behavior for all commands but you can
specify FRCD to force the system to override a state in which the command would normally be denied.
For additional information, including valid command values, refer to the Cisco ONS SONET TL1 Command Guide or
the Cisco ONS SDH TL1 Command Guide .
the Cisco ONS SDH TL1 Command Guide .
Step 12
Click Close to close the TL1 dialog box.
Step 13
Delete the internal patchcords:
a) In node view (single-shelf mode) or multishelf view (multishelf mode), click the Provisioning > WDM-ANS > Internal
Patchcords tabs.
b) Highlight all of the internal patchcords.
c) Click Delete.
d) Click Yes on the confirmation dialog box.
c) Click Delete.
d) Click Yes on the confirmation dialog box.
Step 14
Delete the OSC terminations:
a) Click the Provisioning > Comm Channels > OSC tabs.
b) Highlight all of the OSC terminations.
c) Click Delete.
d) Click Yes on the confirmation dialog box.
b) Highlight all of the OSC terminations.
c) Click Delete.
d) Click Yes on the confirmation dialog box.
Step 15
Remove any amplifier cards (OPT-BST, OPT-PRE) that are installed but not required in the ROADM node.
Step 16
Install the new ROADM cards in the slots identified by your Cisco Transport Planner site plan using the “NTP-G30 Install
the DWDM Cards” task in the chapter “Turn Up a Node” of the Cisco ONS 15454 DWDM Network Configuration Guide.
the DWDM Cards” task in the chapter “Turn Up a Node” of the Cisco ONS 15454 DWDM Network Configuration Guide.
Step 17
Complete the “NTP-G34 Install Fiber-Optic Cables on DWDM Cards and DCUs” procedure in the chapter “Turn Up a
Node” of the Cisco ONS 15454 DWDM Network Configuration Guide for the ROADM node, following the new internal
connections table generated by Cisco Transport Planner.
Node” of the Cisco ONS 15454 DWDM Network Configuration Guide for the ROADM node, following the new internal
connections table generated by Cisco Transport Planner.
Step 18
Complete the “NTP-G152 Create and Verify Internal Patchcords” procedure in the chapter “Turn Up a Node” of the Cisco
ONS 15454 DWDM Network Configuration Guide to recreate the internal patchcords deleted in
ONS 15454 DWDM Network Configuration Guide to recreate the internal patchcords deleted in
Step 13, on page 21
.
Step 19
Complete the NTP-G38 Provision OSC Terminations” procedure in the chapter “Turn Up a Node” of the Cisco ONS 15454
DWDM Network Configuration Guide to recreate the OSC terminations deleted in Step 14.
DWDM Network Configuration Guide to recreate the OSC terminations deleted in Step 14.
Step 20
Import the recalculated ROADM site parameters using the “NTP-G143 Import the Cisco Transport Planner NE Update
Configuration File” procedure in the chapter “Turn Up a Node” of the Cisco ONS 15454 DWDM Network Configuration
Guide.
Configuration File” procedure in the chapter “Turn Up a Node” of the Cisco ONS 15454 DWDM Network Configuration
Guide.
Step 21
Complete the “NTP-G37 Run Automatic Node Setup” task in the chapter “Turn Up a Node” of the Cisco ONS 15454
DWDM Network Configuration Guide.
DWDM Network Configuration Guide.
Step 22
Update the ANS parameters at the adjacent nodes:
a) Display an adjacent node in node view.
21