Cisco Cisco Prime Optical 9.8 Developer's Guide
Cisco Prime Optical 9.8 GateWay/CORBA Programmer Reference Guide
OL-29218-01
635
• Destination zEnd point is not available for TP tunnel creation.
• The protected LSP number protLspNum is already being used by the working LSP.
• The working LSP number workLspNum is already being used by the protected LSP.
• The protected LSP already exists for the TP tunnel.
• The working LSP already exists for the TP tunnel.
• TopologicalLink input is not supported.
• neTPinclusions or neTpSncExclusions is invalid.
• neTpInclusions is invalid. The type is unsupported.
• neTpSncExclusions is invalid. The type is unsupported.
• An internal error occurred while reading rows from the MPLS_LSP_CTP table.
• The protected LSP number protLspNum is already being used by the working LSP.
• The working LSP number workLspNum is already being used by the protected LSP.
• The protected LSP already exists for the TP tunnel.
• The working LSP already exists for the TP tunnel.
• TopologicalLink input is not supported.
• neTPinclusions or neTpSncExclusions is invalid.
• neTpInclusions is invalid. The type is unsupported.
• neTpSncExclusions is invalid. The type is unsupported.
• An internal error occurred while reading rows from the MPLS_LSP_CTP table.
4.13.3 Pseudowire Error Messages
This section lists the pseudowire error messages. The error messages appear if you enter invalid
parameters or values. For valid parameters and values, see:
parameters or values. For valid parameters and values, see:
•
•
The following are the error messages:
• Category is not specified for the enableStatistics parameter.
• You must specify pwClass for managed endpoints.
• You must specify the pseudowire vcID for managed endpoints.
• The pseudowire layer rate must be LR_PW.
• The FD fdName does not exist in the EMS.
• Pseudowire FDFrs must have only one aEnd point.
• You have not entered a value for aEnd.
• Pseudowire FDFrs must have one or two zEnd points for dual-homed protection.
• The specified pseudowire endpoint ptpName is unavailable.
• The egress policy map egrPolMapName is not contained in the ME ME-Name.
• The ingress policy map ingrPolMapName is not contained in the ME ME-Name.
• The table map TabMapName is not contained in the ME ME-Name.
• Available endpoints on ME ME-Name could not be retrieved.
• You must specify pseudowire transmission parameters.
• Redundancy information is missing.
• The necessary free labels within the NE NE-Name could not be retrieved.
• The FDFr name format is invalid.
• checkPWClassCompliancy for node ME-Name failed because pwClass is not specified.
• A connection could not be created on the node ME-Name because the VC ID is in use.
• The operation failed because the VLAN IDs vlanIds are already configured under other
• You must specify pwClass for managed endpoints.
• You must specify the pseudowire vcID for managed endpoints.
• The pseudowire layer rate must be LR_PW.
• The FD fdName does not exist in the EMS.
• Pseudowire FDFrs must have only one aEnd point.
• You have not entered a value for aEnd.
• Pseudowire FDFrs must have one or two zEnd points for dual-homed protection.
• The specified pseudowire endpoint ptpName is unavailable.
• The egress policy map egrPolMapName is not contained in the ME ME-Name.
• The ingress policy map ingrPolMapName is not contained in the ME ME-Name.
• The table map TabMapName is not contained in the ME ME-Name.
• Available endpoints on ME ME-Name could not be retrieved.
• You must specify pseudowire transmission parameters.
• Redundancy information is missing.
• The necessary free labels within the NE NE-Name could not be retrieved.
• The FDFr name format is invalid.
• checkPWClassCompliancy for node ME-Name failed because pwClass is not specified.
• A connection could not be created on the node ME-Name because the VC ID is in use.
• The operation failed because the VLAN IDs vlanIds are already configured under other
service instances.
4.13.4 EVC Error Messages
This section lists the EVC error messages. The error messages appear if you enter invalid
parameters or values. For valid parameters and values, see:
parameters or values. For valid parameters and values, see: