Cisco GainMaker Optoelectronic Node 1GHz with 65 86 MHz Split Installation Guide
Index
sweep generator • 150
System Block Diagram • 96, 114
System Functional Diagrams • 95, 113
System Block Diagram • 96, 114
System Functional Diagrams • 95, 113
T
Test Points • 4
Tips for Optimal Fiber-Optic Connector
Tips for Optimal Fiber-Optic Connector
Performance • 78
To Attach the Fiber Connectors • 23
To Attach the Service Cable Connector • 20
To Calculate the Proper RF Signal Level • 56
To Close the Node Housing • 15
To Complete Reverse Path Balancing • 58
To Configure the Pad on the OIB • 64
To Connect the Coaxial Cable Pin Connector to the
To Attach the Service Cable Connector • 20
To Calculate the Proper RF Signal Level • 56
To Close the Node Housing • 15
To Complete Reverse Path Balancing • 58
To Configure the Pad on the OIB • 64
To Connect the Coaxial Cable Pin Connector to the
Node Housing • 25
To Determine the Output Tilt • 49
To Install Attenuator Pads • 29
To Install Equalizers • 30
To Install the Amplifier Module • 33
To Install the Crowbar Surge Protector • 31
To Install the Node in a Pedestal • 28
To Install the Node on a Strand (Aerial) • 27
To Install the Transmitter Module • 102, 129
To Install the Transponder Module • 43
To Open the Node Housing • 15
To Prepare the Amplifier for Initial Reverse Path
To Install Attenuator Pads • 29
To Install Equalizers • 30
To Install the Amplifier Module • 33
To Install the Crowbar Surge Protector • 31
To Install the Node in a Pedestal • 28
To Install the Node on a Strand (Aerial) • 27
To Install the Transmitter Module • 102, 129
To Install the Transponder Module • 43
To Open the Node Housing • 15
To Prepare the Amplifier for Initial Reverse Path
Balancing • 56
To Prepare the Fiber Connectors • 22
To Remove and Insert AC Shunt Power Directors •
To Remove and Insert AC Shunt Power Directors •
35
To Remove or Reinstall the Optical Receiver • 39
To Remove or Reinstall the Optical Transmitter •
To Remove or Reinstall the Optical Transmitter •
37
To Remove the Status Monitor Transponder
Module • 44
To Remove/Reinstall Dual Redundant Receiver •
41
To Reorient or Replace the Reverse Path Plug-in •
61
To Replace the OIB Plug-in • 62
To Set the Output Level • 50
To Set the Output Tilt • 49
To Stow the Fiber Management Tray • 24
To Trim the Center Conductor • 25
To Unstow the Fiber Management Tray • 22
To Verify the Input Signal Level • 46
Tools • 12
torque • 150
Torque Specifications • 12
Torquing Sequence • 16
Transmitter Module Setup Procedure • 109, 135
To Set the Output Level • 50
To Set the Output Tilt • 49
To Stow the Fiber Management Tray • 24
To Trim the Center Conductor • 25
To Unstow the Fiber Management Tray • 22
To Verify the Input Signal Level • 46
Tools • 12
torque • 150
Torque Specifications • 12
Torquing Sequence • 16
Transmitter Module Setup Procedure • 109, 135
Transmitter Module Troubleshooting Chart • 107,
141
Transmitter Status Indicators • 99
Troubleshooting • 65, 107, 140
Troubleshooting Carrier-to-Noise Problems • 75
TX • 150
Troubleshooting • 65, 107, 140
Troubleshooting Carrier-to-Noise Problems • 75
TX • 150
U
uV • 150
V
V • 150
W
W • 150
Warning
Warning
Radiation • 18
Weight Specifications • 13
OL-29644-03
153