Cisco Cisco Prisma II ICIM 2 Data Sheet
Prisma II Forward Optical Receivers
2
Specifications
Optical
Units
Single
Forward Receiver
High Density
Forward Receiver
Notes
Input Power
dBm
-4 to +5
-8 to +0
Wavelength nm
1280-1600
1280-1600
Optical Return Loss
dB
> 40
> 40
Optical Interface:
SC/APC
SC/APC
Standard
Standard
Electrical
Units
Single
Forward Receiver
High Density
Forward Receiver
Notes
RF Bandwidth
MHz
45 to 1002*
45 to 1002
RF Output Level
dBmV
Use RF output level vs OMI
graph (below)
Use RF output level vs OMI
graph (below)
1,2
Maximum RF Output Level
dBmV
35/ch. For 110 ch’s
36.5/ch. For 78 ch’s
39/ch. for 16 QAM ch’s
36/ch. for 32 QAM ch’s
36/ch. for 32 QAM ch’s
RF Attenuation Range
dB
n/a
0 to 20
RF Attenuation Control
n/a
via LCI or ICIM
Module Responsivity
A/W
dB
≥ 14
≥ 22.9
≥ 17.8
≥ 25.0
3
RF Frequency Response
dB
± 0.5 dB
± 0.5 dB
RF Test Point
dB
-20 (
± 1.0)
-20 (
± 1.0)
RF Return Loss
dB
≥ 16
≥ 16
Tilt
dB
0 to +1
0 to +1
Noise Equivalent Power
pA
√ Hz
≤ 7
≤ 7
Power Consumption
W DC
≤ 15
≤ 7.5
* 870 MHz Forward Receivers are still available
Forward Receiver RF Output Level Vs Optical Modulation Index (OMI)
Single
Forward
Receiver High
Density
Forward
Receiver
32
33
34
35
36
37
38
39
40
41
42
43
3.
0
4.
0
5.
0
6.
0
7.
0
8.
0
OMI per Channel (%)
Minimum
RF Output
Level
per ch
(dBmV)
1
with
+ 3 dBm
Optical
Input
Power
1310nm
1550nm
1550nm
28
29
30
31
32
33
34
35
36
37
38
39
3.
0
4.
0
5.
0
6.
0
7.
0
8.
0
OMI per Channel (%)
Minimum
RF Output
Level
per Ch
(dBmV)
2
with
0 dBm
Optical
Input
Power
1310nm
1550nm
1550nm
Notes:
1.
1.
For the Single Forward Receiver, the graph shows receiver RF output level for the stated Optical Modulation Index (OMI) %, with optical
input power of +3 dBm. To determine RF output levels at other optical input power, add (or subtract) 2 dB in RF level for each 1 dB
increase (or decrease) in receiver optical input power.
input power of +3 dBm. To determine RF output levels at other optical input power, add (or subtract) 2 dB in RF level for each 1 dB
increase (or decrease) in receiver optical input power.
2.
For the High Density Forward Receiver, graph shows receiver RF output level for the stated Optical Modulation Index (OMI) %, with
optical input power of 0 dBm and receiver RF attenuator set to 0 dB. To determine RF output levels at other optical input power, add (or
subtract) 2 dB in RF level for each 1 dB increase (or decrease) in receiver optical input power.
optical input power of 0 dBm and receiver RF attenuator set to 0 dB. To determine RF output levels at other optical input power, add (or
subtract) 2 dB in RF level for each 1 dB increase (or decrease) in receiver optical input power.
3.
Module responsivity measured at 1310 nm with 0 dB RF attenuation, and may change at other wavelengths.
Unless otherwise noted, specifications reflect typical performance and are referenced to the ambient air temperature at the inlet to the
Prisma II chassis. Specifications are based upon measurements made in accordance with SCTE/ANSI standards (where applicable), using
standard frequency assignments.