Intel E3-1260L CM8062301061800 User Manual
Product codes
CM8062301061800
Electrical Specifications
82
Datasheet, Volume 1
7.10
DC Specifications
The processor DC specifications in this section are defined at the processor
pads, unless noted otherwise. See
pads, unless noted otherwise. See
Chapter 8
for the processor land listings and
Chapter 6
for signal definitions. Voltage and current specifications are detailed in
Table 7-5
,
Table 7-6
, and
Table 7-7
.
The DC specifications for the DDR3 signals are listed in
Table 7-8
Control Sideband and
Test Access Port (TAP) are listed in
Table 7-9
.
Table 7-5
through
Table 7-7
list the DC specifications for the processor and are valid
only while meeting the thermal specifications (as specified in the Thermal / Mechanical
Specifications and Guidelines), clock frequency, and input voltages. Care should be
taken to read all notes associated with each parameter.
Specifications and Guidelines), clock frequency, and input voltages. Care should be
taken to read all notes associated with each parameter.
7.10.1
Voltage and Current Specifications
Notes:
1.
1.
Unless otherwise noted, all specifications in this table are based on estimates and simulations or empirical
data. These specifications will be updated with characterized data from silicon measurements at a later
date.
data. These specifications will be updated with characterized data from silicon measurements at a later
date.
2.
Each processor is programmed with a maximum valid voltage identification value (VID) that is set at
manufacturing and cannot be altered. Individual maximum VID values are calibrated during manufacturing
manufacturing and cannot be altered. Individual maximum VID values are calibrated during manufacturing
Table 7-5.
Processor Core Active and Idle Mode DC Voltage and Current Specifications
Symbol
Parameter
Min
Typ
Max
Unit
Note
1
VID
VID Range
0.2500
1.5200
V
2
LL
VCC
V
CC
Loadline Slope
2011D, 2011C, 2011B (processors
with 95 W, 65 W, and 45 W TDPs)
with 95 W, 65 W, and 45 W TDPs)
1.7
m
3, 5, 6
V
CC
TOB
V
CC
Tolerance Band
2011D, 2011C, 2011B (processors
with 95 W, 65 W, and 45 W TDPs)
with 95 W, 65 W, and 45 W TDPs)
PS0
PS1
PS2
PS1
PS2
±16
±13
±13
±11.5
mV
3, 5, 6,
7
V
CC
Ripple
Ripple:
2011D, 2011C, 2011B (processors
with 95 W, 65 W, and 45 W TDPs)
2011D, 2011C, 2011B (processors
with 95 W, 65 W, and 45 W TDPs)
PS0
PS1
PS2
PS1
PS2
±7
±10
-10/+25
mV
3, 5, 6,
7
V
CC,BOOT
Default V
CC
voltage for initial
power up
0
V
I
CC
2011D (processors with 95 W
TDPs) I
TDPs) I
CC
112
A
4
I
CC
2011C (processors with 65 W TDP)
I
I
CC
75
A
4
I
CC
2011B (processors with 45 W TDP)
I
I
CC
60
A
4
I
CC_TDC
2011D (processors with 95 W
TDPs) Sustained I
TDPs) Sustained I
CC
85
A
4
I
CC_TDC
2011C (processors with 65 W TDP)
Sustained I
Sustained I
CC
55
A
4
I
CC_TDC
2011B (processors with 45 W TDP)
Sustained I
Sustained I
CC
40
A
4