Brother CM550DX/ CM550 Operating Guide
65
5
Patterns cannot be welded.
There are some patterns which cannot accept or no overlaps.
There are some patterns which cannot accept or no overlaps.
The message appears when you are welding patterns.
- The patterns do not overlap. Rearrange them so the
- The patterns do not overlap. Rearrange them so the
selected patterns overlap. Unifying the pattern, instead,
can be an alternative editing method depending on your
project.
can be an alternative editing method depending on your
project.
- A pattern that has a seam allowance is selected.
Deactivate the seam allowance setting and weld the
patterns.
patterns.
- An open shape is selected as a pattern. Only closed
shapes can be welded. Unifying the pattern, instead, can
be an alternative editing method depending on your
project.
be an alternative editing method depending on your
project.
Patterns may overlap since seam allowance is set to large on
the machine.
the machine.
When the seam allowance setting for a pattern becomes
larger than with a previous operation, the edges may overlap
nearby patterns. Adjust the seam allowance setting.
Otherwise, increase the spacing between patterns.
larger than with a previous operation, the edges may overlap
nearby patterns. Adjust the seam allowance setting.
Otherwise, increase the spacing between patterns.
Scanning error occurred.
Turn the machine off.
Turn the machine off.
Turn the machine off, then on again, and then try performing
the operation again.
the operation again.
The data cannot be deleted.
The USB flash drive being used may not be usable with this
machine. If unplugging the USB flash drive and performing
the operation again causes the message to appear again,
replace the USB flash drive. For information about USB flash
drive compatible with this machine, visit our website
“ http://solutions.brother.com ”.
machine. If unplugging the USB flash drive and performing
the operation again causes the message to appear again,
replace the USB flash drive. For information about USB flash
drive compatible with this machine, visit our website
“ http://solutions.brother.com ”.
The data cannot be read.
The data cannot be saved.
The mat cannot be recognized.
The mat will unload.
The mat will unload.
A mat that cannot be recognized has been inserted. If a mat
designed specifically for this machine is not being used, use
the specially designed mat.
designed specifically for this machine is not being used, use
the specially designed mat.
Clean the dotted marks at the edge of the mat and their
surrounding area. If the mat is still not recognized, replace
the mat with a new one.
surrounding area. If the mat is still not recognized, replace
the mat with a new one.
There are some patterns which cannot add seam allowance.
The seam allowance settings cannot be specified for
complex pattern shapes. Select a pattern with a simple
shape.
Expanding the seam allowance to 2 mm or more may help.
complex pattern shapes. Select a pattern with a simple
shape.
Expanding the seam allowance to 2 mm or more may help.
There are some patterns which cannot set cutting distance
from the outline.
from the outline.
The cutting distance cannot be specified for complex pattern
shapes. Select a pattern with a simple shape.
shapes. Select a pattern with a simple shape.
There is a pattern included that cannot be saved to USB
media.
Save the pattern in the machine’s memory.
media.
Save the pattern in the machine’s memory.
Depending on the pattern, it may not be possible to save it to
a USB flash drive.
a USB flash drive.
There is a pattern out of the effective area. The pattern
cannot be cut or drawn.
OK to continue?
cannot be cut or drawn.
OK to continue?
There is a pattern(s) outside of the cutting area.
If the pattern(s) outside of the cutting area need(s) not to be
cut out or drawn, continue the operation.
To cut out or draw the pattern(s) outside of the area, increase
the setting for “Cut Area”, or move the pattern(s) into the area
specified with “Cut Area” (page 23).
If the pattern(s) outside of the cutting area need(s) not to be
cut out or drawn, continue the operation.
To cut out or draw the pattern(s) outside of the area, increase
the setting for “Cut Area”, or move the pattern(s) into the area
specified with “Cut Area” (page 23).
This data is too complicated and cannot be converted.
When your are welding or unifying patterns:
Reduce the number of patterns arranged or change the
patterns to ones with simple designs.
Reduce the number of patterns arranged or change the
patterns to ones with simple designs.
This mat cannot be used.
The mat is one that cannot be used with the function being
performed. Replace the mat.
performed. Replace the mat.
Error Messages
Causes / Solutions