Panasonic PT-DW530E User Manual

Page of 4
17.0 mm (0.67 inches) diagonal 
(
16:10 aspect ratio
)
DLP™ chip × 1, DLP™ projection system
2,304,000 (1,920 × 1,200) pixels
1,920 × 1,200 pixels
+60% from centre of screen (manual)
±10% from centre of screen (manual)
16.5 mm (0.65 inches) diagonal 
(
16:10 aspect ratio
)
DLP™ chip × 1, DLP™ projection system
1,024,000 (1,280 × 800) pixels
1,280 × 800 pixels 
(input signals that exceed this resolution will 
be converted to 1,280 × 800 pixels)
+70% from centre of screen (manual)
±10% from centre of screen (manual) 
17.8 mm (0.70 inches) diagonal 
(
4:3 aspect ratio
)
DLP™ chip × 1, DLP™ projection system
786,432 (1,024 × 768) pixels
1,024 × 768 pixels 
(input signals that exceed this resolution will 
be converted to 1,024 × 768 pixels)
+60% from centre of screen (manual)
±10% from centre of screen (manual)
1.02–7.62 m (40–300 inches), 16:10 aspect ratio
4,000 lm (lamp mode: NORMAL)
1.02–7.62 m (40–300 inches), 4:3 aspect ratio
4,500 lm (lamp mode: NORMAL)
100 –240 V AC, 5.0 –1.9 A, 50/60 Hz
415 W (500 VA) (0.3 W at 100 –120 V AC, 0.4 W at 220 –240 V AC with standby mode set to ECO*
1
, 15 W with standby mode set to NORMAL)
Manual zoom (2× zoom), manual focus F 2.0 – 3.4, f 21.5 – 43.0 mm
300 W (max 310 W) UHM lamp
90%
2,000:1 (full on/full off)
f
H
: 27 kHz–100 kHz; f
V
: 24 Hz–120 Hz; dot clock: 25 MHz–162 MHz
f
H
: 15  kHz–100 kHz; f
V
: 24 Hz–120 Hz; dot clock: 162 MHz or lower
f
H
: 15.75 kHz; f
V
: 60 Hz (NTSC/NTSC4.43/PAL-M/PAL60), f
H
: 15.63 kHz; f
V
: 50 Hz (PAL/PAL-N/SECAM)
Vertical: ±40°
Ceiling/floor, front/rear
HDMI 19-pin × 1 (Deep Colour, compatible with HDCP) 
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p, 
VGA (640 × 480) – WUXGA (1,920 × 1,200)*
3
; compatible with non-interlaced signals only; dot clock: 25–162 MHz
Audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz)
DVI-D 24-pin × 1 (DVI 1.0 compliant, compatible with HDCP, compatible with single link only) 
 
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p,
VGA (640 × 480)– WUXGA (1,920 × 1,200)*
3
; compatible with non-interlaced signals only; dot clock: 25 –162 MHz
BNC × 5 (RGB/YP
B
P
R
 × 1)
D-sub HD 15-pin (female) × 1 (RGB/YP
B
P
R
 × 1)
BNC × 1 (composite video)
Mini DIN 4-pin × 1 (S-Video)
RCA × 2 (L, R × 1), 0.5 Vrms
M3 × 1 (L, R × 1), 0.5 Vrms
M3 × 1 (L, R × 1), 0.5 Vrms
M3 × 1 (L, R × 1) (monitor out: 0 – 2.0 Vrms, variable)
D-sub 9-pin (female) × 1 for external control (RS-232C compliant)
D-sub 9-pin (female) × 1 for external control (contact control)
RJ-45 × 1 (for network connection, 10Base-T/100Base-TX, compliant with PJLink™)
Moulded plastic (PC+ABS)
332 × 168*
4
 × 484.5 mm (13-1/16˝ × 6-5/8˝ *
4
 × 19-1/16˝ ) (including the lens)
Approximately 8.5 kg (18.7 lbs.)
Operating temperature: 0°C– 45°C (32°F– 113°F); operating humidity: 20%–80% (no condensation)
Power cord with security lock, wireless remote control unit, batteries for remote control (R6/LR6 type × 2), wire rope, 
software CD-ROM (Logo Transfer Software, Multi Projector Monitoring & Control Software Ver. 2, Wireless Manager ME 5.5)
f
H
: 15.75 kHz; f
V
: 60 Hz (480i [525i])
f
H
: 31.50 kHz; f
V
: 60 Hz (480p [525p])
f
H
: 15.63 kHz; f
V
: 50 Hz (576i [625i])
f
H
: 31.25 kHz; f
V
: 50 Hz (576p [625p])
f
H
: 37.50 kHz; f
V
: 50 Hz (720 [750]/50p)
f
H
: 45.00 kHz; f
V
: 60 Hz (720 [750]/60p)
f
H
: 33.75 kHz; f
V
: 60 Hz (1035/60i)
f
H
: 33.75 kHz; f
V
: 60 Hz (1080 [1125]/60i)
f
H
: 28.13 kHz; f
V
: 50 Hz (1080 [1125]/50i)
f
H
: 28.13 kHz; f
V
: 25 Hz (1080/25p)
f
H
: 27.00 kHz; f
V
: 24 Hz (1080/24p)
f
H
: 27.00 kHz; f
V
: 48 Hz (1080/24sF)
f
H
: 33.75 kHz; f
V
: 30 Hz (1080/30p)
f
H
: 67.50 kHz; f
V
: 60 Hz (1080/60p)
f
H
: 56.25 kHz, f
V
: 50 Hz (1080/50p)
Model
Power supply
Power consumption
DLP™ chip
Lens
Lamp
Screen size (diagonal)
Brightness*
2
Centre-to-corner uniformity*
2
Contrast*
2
Resolution
Scanning 
frequency
Optical axis shift
Keystone correction range
Installation
Terminals
Cabinet materials
Dimensions (W x H x D)
Weight
Operating environment
Supplied accessories
HDMI/DVI-D
RGB
YP
B
P
R
 (YC
B
C
R
)
Video/S-Video
Vertical
Horizontal
HDMI IN
DVI-D IN
RGB 1 IN
RGB 2 IN
VIDEO IN
S-VIDEO IN
AUDIO IN 1
AUDIO IN 2
AUDIO IN 3
AUDIO OUT
SERIAL IN
REMOTE IN
LAN
PT-
DW530E
PT-
DX500E
PT-
DZ570E
Specifications
*1  When the standby mode is set to ECO, network functions such as power on over the LAN will not operate. Also, only certain commands can be received for external control using
the serial terminal.
*2  Measurement, measuring conditions and method of notation all comply with ISO 21118 international standards.
*3  Compliant with VESA CVT-RB.
*4  With legs at shortest position.
1.   Do not install the projector in locations that are subject to excessive water, humidity, steam or oily smoke. Doing so may result in fire, mal-
function or electric shock.
2.  The projector uses a high-voltage mercury lamp that contains high internal pressure. This lamp may break, emitting a large sound, or fail to 
illuminate, due to impact or extended use.
3.  The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions: 
•  Never place objects on top of the projector while it is in operation.
•  Make sure there is an unobstructed space of 500 mm (19-11/16 in) or more around the projector’s exhaust openings.
•  Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection. 
  When stacking projector units, be sure to provide the amount of space indicated between them. These space requirements also apply to 
installation where only one projector unit is operating at one time and the other unit is used as a backup.
•  If the projector is placed in a box or enclosure, the temperature of the air surrounding the projector must be between 0°C (32°F) and 40°C 
(104°F). Also, make sure the projector’s intake and exhaust openings are not blocked. Take particular care to ensure that hot air from the 
exhaust openings is not sucked into the intake.
4.  The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.
• The length of time that it takes for the lamp to break or fail to illuminate varies greatly depending on individual lamp characteristics and 
usage conditions.
•  The brightness of the lamp will gradually decrease with use.
5.  Due to natural characteristics of lamps, screen brightness may vary (flicker). This is not an indication of faulty lamp performance.
N OT E S   O N   U S E
Optional Accessories
ET-PKD110H
Ceiling mount
bracket
for high ceilings
ET-PKD110S
Ceiling mount bracket
for low ceilings
ET-WM200E
Wireless module
ET-LAD60A
Replacement lamp unit
ET-LAD60AW
Replacement lamp unit
(twin pack)
1.02 m
1.52 m
2.03 m
2.54 m
3.81 m
5.08 m
7.62 m
1.23
1.87
2.51
3.15
4.75
6.35
9.55
2.51
3.79
5.07
6.34
9.53
12.73
19.11
-0.05
-0.08
-0.11
-0.14
-0.20
-0.27
-0.40
0.27
0.40
0.54
0.67
1.01
1.35
2.02
40˝
60˝
80˝
100˝
150˝
200˝
300˝
(4.1)
(6.2)
(8.3)
(10.4)
(15.6)
(20.9)
(31.4)
(8.2)
(12.4)
(16.6)
(20.8)
(31.2)
(41.7)
(62.6)
(-0.2
(-0.3
(-0.4
(-0.4
(-0.7
(-0.9
(-1.3
0.9)
1.3)
1.8)
2.2)
3.3)
4.4)
6.6)
Projection size
(diagonal)
Projection distance
Min 
(wide)
Max
(telephoto)
PT-DZ570 - E (16:10)
Height from edge 
of screen to centre 
of lens
PT-DZ570E (16:10 aspect ratio; throw ratio: 1.45 –2.94:1)
unit: metres (feet)
Projection Distance
1.02 m
1.52 m
2.03 m
2.54 m
3.81 m
5.08 m
7.62 m
1.29
1.96
2.64
3.31
4.99
6.67
10.03
2.64
3.98
5.32
6.66
10.01
13.36
20.07
-0.11
-0.16
-0.22
-0.27
-0.40
-0.54
-0.81
0.27
0.40
0.54
0.67
1.01
1.35
2.02
40˝
60˝
80˝
100˝
150˝
200˝
300˝
(4.3)
(6.5)
(8.7)
(10.9)
(16.4)
(21.9)
(33.0)
(8.6)
(13.0)
(17.4)
(21.8)
(32.8)
(43.8)
(65.8)
(-0.4
(-0.5
(-0.7
(-0.9
(-1.3
(-1.8
(-2.7
0.9)
1.3)
1.8)
2.2)
3.3)
4.4)
6.6)
Projection size
(diagonal)
Projection distance
Min 
(wide)
Max
(telephoto)
PT-DW530 - E (16:10)
Height from edge 
of screen to centre 
of lens
PT-DW530E (16:10 aspect ratio; throw ratio: 1.53– 3.09:1)
1.02 m
1.52 m
2.03 m
2.54 m
3.81 m
5.08 m
7.62 m
1.20
1.82
2.45
3.08
4.64
6.21
9.34
2.46
3.70
4.95
6.20
9.32
12.44
18.68
-0.06
-0.09
-0.12
-0.15
-0.23
-0.31
-0.46
0.31
0.46
0.61
0.76
1.14
1.52
2.29
40˝
60˝
80˝
100˝
150˝
200˝
300˝
(4.0)
(6.0)
(8.1)
(10.1)
(15.3)
(20.4)
(30.7)
(8.0)
(12.1)
(16.2)
(20.3)
(30.5)
(40.8)
(61.2)
(-0.2
(-0.3
(-0.4
(-0.5
(-0.8
(-1.0
(-1.5
1.0)
1.5)
2.0)
2.5)
3.8)
5.0)
7.5)
Projection size
(diagonal)
Projection distance
Min 
(wide)
Max
(telephoto)
PT-DX500 - E (4:3)
Height from edge 
of screen to centre 
of lens
PT-DX500E (4:3 aspect ratio; throw ratio: 1.51–3.05:1)
Dimensions
168
(6-5/8)
332
(13-1/16)
484.5
(19-1/16)
unit: millimetres (inches)
Terminals
1.  LAN  connector
2.  HDMI  input
3.  Video  input
4.  S-Video  input
5.  RGB  1  input
6.  RGB  2  input
7.  DVI-D  input
8.  Audio  1  input
9.  Audio  2  input
10.  Audio  3  input
11.  Audio  output
12.  Remote  input
13.  Serial  input
1
2
3
4
5
6
7
8
9
10 11
12
13
The photo shows the PT-DZ570E/DW530E.
Note that the DVI-D input terminal
 on the
PT-DX500E is located between the LAN
connector and the HDMI input.
JQA-0443
051
EC98J2010
Factories of Systems Business Group have received ISO 14001:2004—
the Environmental Management System certification (except for third 
parties’ peripherals).
Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product may be subject to export 
regulations. All other trademarks are the property of their respective trademark owners. Projection images simulated. DLP, DLP logo and DLP 
Medallion logo are trademarks or registered trademarks of Texas Instruments. © 2010 Panasonic Corporation. All rights reserved.
PT-DZ570E1 Printed in Japan.
All information included here is valid as of November 2010.
http://panasonic.net/avc/projector
For more information about Panasonic projectors