Alpine CDA-9886R User Manual
31
-EN
1
After selecting Parametric EQ from the Sound Field
Adjustment mode, press BAND/TA to select the
band to be adjusted.
Adjustment mode, press BAND/TA to select the
band to be adjusted.
Band1
Band2
Band3
Band4
Band5
Band1
2
Press
or
to select frequency bands.
Adjustable frequency bands:
20 Hz to 20 kHz (in 1/3 octave steps)
20 Hz to 20 kHz (in 1/3 octave steps)
Band-1: 20 Hz~80 Hz (63 Hz)
Band-2: 50 Hz~200 Hz (150 Hz)
Band-3: 125 Hz~3.2 kHz (400 Hz)
Band-4: 315 Hz~8 kHz (1 kHz)
Band-5: 800 Hz~20 kHz (2.5 kHz)
3
Turn the Rotary encoder to adjust the level.
Adjustable level: -6 to +6 dB
4
Press SOURCE/
to set the bandwidth (Q).
Adjustable bandwidth: 1, 1.5, 3
5
To adjust another band, repeat steps 1 to 4 and
adjust all bands.
adjust all bands.
• The frequencies of adjacent bands cannot be adjusted within 4 steps.
• While adjusting the Parametric EQ, you should consider the
• While adjusting the Parametric EQ, you should consider the
frequency response of the connected speakers.
Adjusting the Graphic Equalizer Curve
You can modify the equalizer settings to create a response curve more
appealing to your personal taste. To adjust the graphic equalizer curve,
set the EQ mode to Graphic EQ. For details, refer to “Setting EQ mode”
(page 30).
appealing to your personal taste. To adjust the graphic equalizer curve,
set the EQ mode to Graphic EQ. For details, refer to “Setting EQ mode”
(page 30).
1
After selecting Graphic EQ from the Sound Field
Adjustment mode, press BAND/TA to select the
band to be adjusted.
Adjustment mode, press BAND/TA to select the
band to be adjusted.
Band1
Band2
Band3
Band4
Band5
Band6
Band7
Band1
Band-1 (63 Hz) / Band-2 (150 Hz) / Band-3 (400 Hz) /
Band-4 (1 kHz) / Band-5 (2.5 kHz) / Band-6 (6.3 kHz) /
Band-7 (17.5 kHz)
2
Turn the Rotary encoder to adjust the level.
Adjustable output level: -6 to +6 dB
3
To adjust another band, repeat steps 1 and 2, and
then adjust all bands.
then adjust all bands.
Adjusting the Time Correction
Before performing the following procedures, refer to “About Time
Correction” (page 33).
Correction” (page 33).
1
After selecting Time Correction from the Sound Field
Adjustment mode, press BAND/TA to select a
speaker to be adjusted.
Adjustment mode, press BAND/TA to select a
speaker to be adjusted.
2.2ch (3WAY) System
4.2ch (FRONT/REAR/SUBW.) System
2
Turn the Rotary encoder to adjust the distance
(0.0 to 336.6cm).
L = (distance to farthest speaker) – (distance to other
speakers)
Refer to “Time Correction Value List” on page 33.
3
Repeat steps 1 and 2 to set another speaker.
By setting these values to make its sound reach the
listening position at the same time as the sound of other
speakers.
listening position at the same time as the sound of other
speakers.
Adjusting the Crossover Settings
Before performing the following procedures, refer to “About the
Crossover” (page 34).
Crossover” (page 34).
2.2ch (3WAY) System
1
After selecting X-Over from the Sound Field
Adjustment mode, press BAND/TA to select the
band to be adjusted.
Adjustment mode, press BAND/TA to select the
band to be adjusted.
2.2ch (3WAY) System / NORMAL (L=R)
Setting items:
LOW / MID-L / MID-H / HIGH
2.2ch (3WAY) System / INDIVIDUAL (L/R)
Setting items:
LOW-L / LOW-R / MID-L-L / MID-L-R / MID-H-L /
MID-H-R / HIGH-L / HIGH-R
2
Press
or
to select the desired cut-off frequency
(Crossover Point).
Adjustable frequency bands:
2.2ch (3WAY) System
Setting items:
LOW / MID-L 20 Hz~200 Hz
MID-H
MID-H
20 Hz~20 kHz
HIGH
(1 kHz~20 kHz)
*
1
/(20 Hz~20 kHz)
*
2
*
1
When Maker’s is selected, refer to “Setting the Response Slope for
the High Range Speaker (TW Setup)” (page 30).
the High Range Speaker (TW Setup)” (page 30).
*
2
When User’s is selected, refer to“Setting the Response Slope for the
High Range Speaker (TW Setup)” (page 30).
High Range Speaker (TW Setup)” (page 30).
F-L (Initial setting)
F-R
R-L
R-R
(Mid-L)
(Mid-R) (High-L ) (High-R)
SW-L
SW-R
F-L
(Mid-L)
F-L (Initial setting)
F-R
R-L
R-R
(Front-L)
(Front-R) (Rear-L) (Rear-R)
SW-L
SW-R
F-L
(Front-L)