Alpine dva-9965r User Manual
27
-EN
ALPINE DVA-9965R 68-02065Z31-A (EN)
Adjusting and Storing the Crossover
Settings
Settings
Before performing the following procedures, refer to “About the
Crossover” (page 26).
Crossover” (page 26).
1
Press and hold MENU for at least 2 seconds.
2
Select the Crossover mode by sliding your finger
on the GlideTouch bar to the left or right. Press
the GlideTouch bar under the Crossover mode.
on the GlideTouch bar to the left or right. Press
the GlideTouch bar under the Crossover mode.
2 WAY System
3
Press BAND to select the band to be adjusted.
SUBW
→ REAR → FRONT → SUBW
4
Select the desired cut-off frequency (Crossover
Point) by sliding your finger on the GlideTouch
bar to the left or right.
Point) by sliding your finger on the GlideTouch
bar to the left or right.
Adjustable frequency bands: 20Hz to 200Hz
(in 1/3 octave steps)
5
Press SOURCE/POWER to adjust the slope.
Adjustable slope: FLAT, 6dB/oct., 12dB/oct.,
18dB/oct., 24dB/oct.
6
Adjust the output level by turning the Rotary
encoder.
encoder.
Adjustable output level: -12 to 0 dB.
7
To adjust another band, repeat steps 3 to 6, then
adjust all bands.
adjust all bands.
8
When the setting has been completed, press
FUNC. or the GlideTouch bar to activate the
preset mode.
FUNC. or the GlideTouch bar to activate the
preset mode.
9
Select any one of the preset numbers (1 through 6)
by sliding your finger on the GlideTouch bar to
the left or right. Press and hold the GlideTouch
bar under the desired preset for at least 2 seconds.
The adjustments are saved in the selected preset.
by sliding your finger on the GlideTouch bar to
the left or right. Press and hold the GlideTouch
bar under the desired preset for at least 2 seconds.
The adjustments are saved in the selected preset.
10
After setting, press and hold MENU for at least 2
seconds to return to normal mode.
seconds to return to normal mode.
• If MENU is pressed while adjusting or setting items in the MENU
mode, the unit returns to the previous selection screen.
• By pressing the GlideTouch bar under RETURN in the MENU
mode, the unit returns to the normal mode.
• If no operation is performed for 60 seconds, the unit returns to
normal mode.
3 WAY System
3
Press BAND to select the band to be adjusted.
LOW
→ MID-L → MID-H → HIGH → LOW
4
Select the desired cut-off frequency (Crossover
Point) by sliding your finger on the GlideTouch
bar to the left or right.
Point) by sliding your finger on the GlideTouch
bar to the left or right.
Adjustable frequency bands:
LOW
LOW
: 20Hz to 200Hz (in 1/3 octave steps)
MID-L*
1
: 20Hz to 200Hz (in 1/3 octave steps)
MID-H*
2
: 1kHz to 20kHz (in 1/3 octave steps)
HIGH
: 1kHz to 20kHz (in 1/3 octave steps)
*
1
: Midrange high-pass filter is adjusted.
*
2
: Midrange low-pass filter is adjusted.
5
Press SOURCE/POWER to adjust the slope.
Adjustable slope: FLAT*, 6dB/oct., 12dB/oct.,
18dB/oct., 24dB/oct.
* FLAT can be set for the HIGH slope only when USER'S
is selected in “Setting the Response Slope for the High
Range Speaker (TW SETUP)” (page 39). Depending on
the response characteristics of the speaker, care should
be taken when setting the response slope to FLAT, as
speaker damage may result. With the DVA-9965R, a
message is displayed when the response slope for the
high range speaker is set to FLAT. After the message is
displayed, press the Rotary encoder to set to FLAT.
Range Speaker (TW SETUP)” (page 39). Depending on
the response characteristics of the speaker, care should
be taken when setting the response slope to FLAT, as
speaker damage may result. With the DVA-9965R, a
message is displayed when the response slope for the
high range speaker is set to FLAT. After the message is
displayed, press the Rotary encoder to set to FLAT.
6
Adjust the output level by turning the Rotary
encoder.
encoder.
Adjustable output level: -12 to 0 dB.
7
To adjust another band, repeat steps 3 to 6, then
adjust all bands.
adjust all bands.
8
When the setting has been completed, press
FUNC. or the GlideTouch bar to activate the
preset mode.
FUNC. or the GlideTouch bar to activate the
preset mode.
9
Select any one of the preset numbers (1 through 6)
by sliding your finger on the GlideTouch bar to
the left or right. Press and hold the GlideTouch
bar under the desired preset for at least 2 seconds.
The adjustments are saved in the selected preset.
by sliding your finger on the GlideTouch bar to
the left or right. Press and hold the GlideTouch
bar under the desired preset for at least 2 seconds.
The adjustments are saved in the selected preset.
10
After setting, press and hold MENU for at least 2
seconds to return to normal mode.
seconds to return to normal mode.
• If MENU is pressed while adjusting or setting the items in the
MENU mode, the unit returns to the previous selection screen.
• By pressing the GlideTouch bar under RETURN in the MENU
mode, the unit returns to the normal mode.
• If no operation is performed for 60 seconds, the unit returns to
normal mode.
• About the 2way/3way system
You can switch to 2way/3way system mode with the 2way/3way
switch on the bottom side of the unit (page 68, 69 and 71).
switch on the bottom side of the unit (page 68, 69 and 71).
When setting to “3 WAY”:
The unit can be operated in a 3 way system.
When setting to “F/R/Sub-W”:
The unit can be operated in a 2 way system.
F/R/Sub-W
3WAY