andi pyrolytic ax100 mtpc User Manual
OVEN CLEANING
CLEANING SAFETY
Turn off all controls and wait for appliance parts to cool before touching or cleaning them. Clean appliance with
caution. Use care to avoid steam burns if a wet sponge or clothe is used to wipe spills on a hot surface. Some cleaners
can produce noxious fumes if applied to a hot surface.
Turn off all controls and wait for appliance parts to cool before touching or cleaning them. Clean appliance with
caution. Use care to avoid steam burns if a wet sponge or clothe is used to wipe spills on a hot surface. Some cleaners
can produce noxious fumes if applied to a hot surface.
SURFACE CLEANING
This is easily done using a damp cloth and a non-abrasive detergent, wipe using a soft dry cloth. For stainless steel parts
with stubborn soils, use only plastic scrubbing pad or a sponge with vinegar and warm water. For Oven cooking cavity
cleaning, follow the same procedure mentioned above, but to ease the cleaning you may start cleaning when the cooking
cavity is still warm enough to be touched.
This is easily done using a damp cloth and a non-abrasive detergent, wipe using a soft dry cloth. For stainless steel parts
with stubborn soils, use only plastic scrubbing pad or a sponge with vinegar and warm water. For Oven cooking cavity
cleaning, follow the same procedure mentioned above, but to ease the cleaning you may start cleaning when the cooking
cavity is still warm enough to be touched.
OVEN DOOR:
To remove and replace the Oven Door, please follow procedures here below;
REMOVING OVEN DOOR:
Fully open the oven door. – Raise the U-clip over the hook on each of the hinges to the “locked” position, see figure 5
and 6. This will prevent the hinge from snapping closed when the door is removed. – Grasp the door by the sides toward
the back. – Raise the front of the door several centimetres (there will be some spring resistance to overcome because of
the hinge being locked). – When the front of the door is high enough, you will be able to lift the hinges to clear the
indents. – Pull the hinges out of the slots in the oven front frame.
Fully open the oven door. – Raise the U-clip over the hook on each of the hinges to the “locked” position, see figure 5
and 6. This will prevent the hinge from snapping closed when the door is removed. – Grasp the door by the sides toward
the back. – Raise the front of the door several centimetres (there will be some spring resistance to overcome because of
the hinge being locked). – When the front of the door is high enough, you will be able to lift the hinges to clear the
indents. – Pull the hinges out of the slots in the oven front frame.
TO REPLACE THE OVEN DOOR:
Grasp the sides of the door at the centre and inert the ends of the hinges into the slots in the oven front frame as far as
they will go, see figure 5 and 6. – With the door open all the way, lower the two locking clips. – Raise the oven door
and make sure that it fits evenly with the front sides.
Grasp the sides of the door at the centre and inert the ends of the hinges into the slots in the oven front frame as far as
they will go, see figure 5 and 6. – With the door open all the way, lower the two locking clips. – Raise the oven door
and make sure that it fits evenly with the front sides.
WARNING. Never release the U-clip levers when the door is off. Do not close the hinges. Without the weight of the
door, the powerful springs will snap the hinges closed with great force.
CAUTION: Do not place excessive weight on or stand on an open oven door. This could break the door or injure the
user. Also, do not attempt to open or close door or operate oven until door is properly replaced.
door, the powerful springs will snap the hinges closed with great force.
CAUTION: Do not place excessive weight on or stand on an open oven door. This could break the door or injure the
user. Also, do not attempt to open or close door or operate oven until door is properly replaced.
REPLACING THE OVEN LIGHT
WARNING; To prevent electrical shock and/or personal injury read follow this procedure:
Before replacing the light bulb, be sure the electric power is turned off at the circuit breaker.
Be sure the oven and light bulb are cool. Then remove light cover A by unscrewing it. Figure 7.
Do not touch hot bulb with a damp cloth as this may cause the bulb to break.
Replace light bulb with a 25 W – 230 V AC appliance bulb only. Figure 7.
If the light cover is damaged or broken, do not use the oven until a new cover is in place.
Do not operate the oven unless the light cover is securely in position.
SPARE PARTS.
Only authorised parts may be used in performing service on the appliance. Do not repair or replace any part of the
appliance unless specifically recommended in the manual. All other services should be referred to a qualified technician.
To request a product spare part, you must indicate the following product information:
1) Appliance or product model and serial production number which are indicated on product data label, placed on the
front-bottom of oven cooking cavity.
2) Spare part description and part number, technical information available only by authorised technical service centre.
3) And finally, also indicate information on the distributor that sold the appliance as well as your nearest technical
service centre.
Only authorised parts may be used in performing service on the appliance. Do not repair or replace any part of the
appliance unless specifically recommended in the manual. All other services should be referred to a qualified technician.
To request a product spare part, you must indicate the following product information:
1) Appliance or product model and serial production number which are indicated on product data label, placed on the
front-bottom of oven cooking cavity.
2) Spare part description and part number, technical information available only by authorised technical service centre.
3) And finally, also indicate information on the distributor that sold the appliance as well as your nearest technical
service centre.
4