American Audio Q-Spand Pro User Manual
©
American Audio
®
- www.americanaudio.us - Q-SPAND PRO Instruction Manual Page 13
Q-SPAND PRO
REAR PANEL - CONTROLS AND FUNCTIONS
32. GND (GROUND TERMINAL) - Be sure to connect turntable ground leads to either or both of
the two available ground terminals. This will reduce the humming and popping noises associated
with magnetic phono cartridges.
33. MICROPHONE 3 CONNECTOR - This jack is used to a connect a microphone to the mixer. Con-
nect you microphone via this 1/4 inch (6.3mm) jack. This microphone will be controlled through the
channel 4 fader. The channel 4 EQ will also effect the microphone output. Be sure to flip the SOURCE
SELECTOR SWITCH (4) to the “MIC 3” position to operate this microphone’s input signal.
34. MICROPHONE 2 CONNECTOR - This jack is used to a connect a microphone to the mixer.
Connect you microphone via this 1/4 inch (6.3mm) jack. The volume output level for this microphone
will be controlled by its own respective VOLUME KNOB (30).
35. MIC ATTENUATOR - This knob is used to adjust the MIC 1 and MIC 2 input level.
36. CHANNEL LINE LEVEL SELECTOR SWITCHES - These switches are used to change the volt-
age line levels of there respected Phono / Aux RCA inputs jacks. When connecting turntables with
magnetic cartridges to these jacks be sure the corresponding switch is in the “PHONO” position,
and when using line level input devices be sure this switch is in the “AUX” position. Always be sure
main power is shut off before change the position of the Line Level Selector Switch.
37. CHANNEL 1: PHONO 1/AUX 1 INPUT - The type of input must directly reflect the selected mode
of the LINE LEVEL SELECTOR SWITCH (36). Turntables equipped with MM pickup cartridge (All DJ
turntable use MM pick-up cartridges) may be connected to these jacks as long as the LINE LEVEL
SELECTOR SWITCH (36) is in the “PHONO 1” position. CD players, Tape Decks and other line level
instruments may only be connected to these jacks as long as the LINE LEVEL SELECTOR SWITCH
(36) is in the “AUX 1” position. Never connect line level instruments (CD players, tape decks, etc.)
to these jacks when the LINE LEVEL SELECTOR SWITCH (36) is in the “PHONO 1” position, THIS
MAY SERIOUSLY DAMAGE YOUR MIXER! The red colored RCA jack represents the right channel
input and the white represents the left channel input. Input volume will be controlled by the channel
one fader. The channel SOURCE SELECTOR SWITCH (4) must be in the "Phono 1/Aux 1" position,
to monitor any source connected to these jacks.
CHANNEL 1: LINE 1 INPUT JACKS - DO NOT CONNECT TURNTABLES TO THESE JACKS!
CD players, Tape Decks and other line level instruments may be connected to these jacks. The red
colored RCA jack represents the right channel input and the white represents the left channel input.
Input volume will be controlled by channel one fader. The channel SOURCE SELECTOR SWITCH (4)
must be in the "Line 1" position, to monitor any source connected to these jacks.
38. CHANNEL 2: PHONO 2/AUX 2 INPUT - The type of input must directly reflect the selected mode
the two available ground terminals. This will reduce the humming and popping noises associated
with magnetic phono cartridges.
33. MICROPHONE 3 CONNECTOR - This jack is used to a connect a microphone to the mixer. Con-
nect you microphone via this 1/4 inch (6.3mm) jack. This microphone will be controlled through the
channel 4 fader. The channel 4 EQ will also effect the microphone output. Be sure to flip the SOURCE
SELECTOR SWITCH (4) to the “MIC 3” position to operate this microphone’s input signal.
34. MICROPHONE 2 CONNECTOR - This jack is used to a connect a microphone to the mixer.
Connect you microphone via this 1/4 inch (6.3mm) jack. The volume output level for this microphone
will be controlled by its own respective VOLUME KNOB (30).
35. MIC ATTENUATOR - This knob is used to adjust the MIC 1 and MIC 2 input level.
36. CHANNEL LINE LEVEL SELECTOR SWITCHES - These switches are used to change the volt-
age line levels of there respected Phono / Aux RCA inputs jacks. When connecting turntables with
magnetic cartridges to these jacks be sure the corresponding switch is in the “PHONO” position,
and when using line level input devices be sure this switch is in the “AUX” position. Always be sure
main power is shut off before change the position of the Line Level Selector Switch.
37. CHANNEL 1: PHONO 1/AUX 1 INPUT - The type of input must directly reflect the selected mode
of the LINE LEVEL SELECTOR SWITCH (36). Turntables equipped with MM pickup cartridge (All DJ
turntable use MM pick-up cartridges) may be connected to these jacks as long as the LINE LEVEL
SELECTOR SWITCH (36) is in the “PHONO 1” position. CD players, Tape Decks and other line level
instruments may only be connected to these jacks as long as the LINE LEVEL SELECTOR SWITCH
(36) is in the “AUX 1” position. Never connect line level instruments (CD players, tape decks, etc.)
to these jacks when the LINE LEVEL SELECTOR SWITCH (36) is in the “PHONO 1” position, THIS
MAY SERIOUSLY DAMAGE YOUR MIXER! The red colored RCA jack represents the right channel
input and the white represents the left channel input. Input volume will be controlled by the channel
one fader. The channel SOURCE SELECTOR SWITCH (4) must be in the "Phono 1/Aux 1" position,
to monitor any source connected to these jacks.
CHANNEL 1: LINE 1 INPUT JACKS - DO NOT CONNECT TURNTABLES TO THESE JACKS!
CD players, Tape Decks and other line level instruments may be connected to these jacks. The red
colored RCA jack represents the right channel input and the white represents the left channel input.
Input volume will be controlled by channel one fader. The channel SOURCE SELECTOR SWITCH (4)
must be in the "Line 1" position, to monitor any source connected to these jacks.
38. CHANNEL 2: PHONO 2/AUX 2 INPUT - The type of input must directly reflect the selected mode
32
36
39
43
44
45
46
47
48
38 36 37 36 35 34
42 41 40
33