Arcam CD192 User Manual

CD192

CD192

Using the CR-314 remote control

NOTE: Remember to install the two AAA batteries 
supplied before trying to use your remote control.
Do not place anything in front of the display area 
on the CD player (where the IR receiver is located), 
or the remote control may not work.
Note that greyed-out buttons on the remote control 
are DVD-specific and are not used with the CD 
player. 

CR-314

RPT

CLEAR

0

PROG

A-B

7

8

9

DISP

4

5

6

CD

DVD

1

2

3

OK

OPEN

MUTE

P

MODE

CD/DVD  REMOTE

CD

DVD

SUBT

ZOOM

AUDIO

MEM

RTN

ANGLE

SETUP

STATUS

SRCH

MENU

TITLE

CD/DVD 

Ensure that CD mode is selected using the 

 

toggle button. The ‘CD’ LED above the 

 

button is lit briefly when CD mode is selected.

DISP (display) 

Turns the display on or off. Turning the display off 

generally produces a slight improvement in sound 

quality. 

A–B 

This button enables you to repeat any section of music 

within a track. Whilst the disc is playing, press the 

 

button at the start of the section you wish to repeat. 

‘REPEAT’ is shown on the display and the letter ‘A–’ 

flashes. Press the button a second time when you reach 

the end of the section you wish to repeat. The ‘A–B’ 

letters stop flashing and remain lit. This section will 

repeat until you press   or 

 or 

. The forward search 

button (

) moves forward within the selected loop.

To repeat the entire CD or a pre-programmed selection 

of tracks press 

 once: ‘REPEAT’ lights on the display. 

To repeat a particular track, select that track and then 

press 

 twice so that ‘REPEAT 1’ is shown on the 

display. If you now select a different track, that track is 

repeated instead.

To cancel the repeat function press 

 a third time.

CLEAR
If you make a mistake whilst programming you can 
delete the last entered track by pressing 

. 

To delete all the programmed tracks, press 

 

repeatedly until ‘0’ is displayed.
To exit the program facility, press 

.

Press 

 once to display the remaining time of the 

currently playing track. Press again to display the time 

remaining of the disc. Press a third time to turn the text 

display on. 

Press 

 again and the display reverts to its original 

setting, showing the time elapsed for the current track.

For CDs with text, pressing 

 once while the disc is 

loaded but not playing displays the artist’s name.

Pressing 

 a second time displays the total number 

of tracks and the total playing time.

0–9 keypad
This allows direct access to individual tracks on the disc. 
To select a track, press the corresponding keypad button. 
For tracks greater than 9, enter the digits in sequence. 
For example, to play track 15, press and hold 

 until the 

number on the display moves to the left, then press 

.

PROG (Program) 
You can program a selection of up to 24 tracks from 
a disc to play in any order. Select a track by using the 

 and 

 buttons, then press 

 to program the 

track into memory (‘PROGRAM’ appears on the display 
to indicate that you have started programming a 
sequence). Repeat these steps to program the remaining 
tracks in your selection. Alternatively, press 

 once 

and enter your track selection using the 0–9 keypad.
The display shows the track numbers programmed, 
the total length of the programmed sequence and the 
number of tracks programmed (shown by a number 
below the word ‘STEP’). 
Each time you enter a track the number below ‘STEP’ 
increments by one and flashes until you press 

 

to confirm. If you fail to press 

 within about five 

seconds the display stops flashing and you will have to 
reselect the track.
Press 

to play the program. Press   again to replay the 

entire sequence from the start. Press and hold 

 to 

erase the programmed sequence. Press 

 again to 

exit the program facility.

MUTE 
Stops sound to the speaker outputs of certain Arcam 
amplifiers.

Volume +/– 
Adjusts the volume on Arcam remote-controllable 
amplifiers.
Note that the volume (+/–) controls and 

 button 

have no effect on the audio output level of the CD 
players.

Opens and closes the CD tray

Search backwards and forwards;

Skip track backwards and forwards (see page 5)

Pause, Play and Stop (see page 5)

Press once to shuffle play CD tracks (i.e. play them in 

a random order). Press again to cancel shuffle play.