Arcam dv27 User Manual
12
13
E
n
g
li
sh
Using the remote control
OK
ANGLE
CD
DVD
SETUP
STATUS
SRCH
ZOOM
AUDIO
MEM
RTN
P
MODE
SUBT
TITLE
MENU
RPT
CLEAR
0
PROG
A-B
7
8
9
DISP
4
5
6
CD
DVD
1
2
3
MUTE
OPEN
CD/DVD REMOTE
CR-314
NOTE: Remember to install the two AAA batteries
supplied before trying to use your remote control.
Do not place anything in front of the FMJ badge on the
front panel (where the IR receiver is located), or the
remote control may not work.
supplied before trying to use your remote control.
Do not place anything in front of the FMJ badge on the
front panel (where the IR receiver is located), or the
remote control may not work.
Volume +/–
Adjusts the volume on Arcam remote-controllable amplifiers.
Note that the volume (
+
/
–
) controls and
MUTE
button have no
effect on the audio output level of the DVD players.
MUTE
Stops sound to the speaker outputs of certain Arcam amplifiers.
OPEN
Opens and closes the disc tray.
Playback control
PAUSE
( ),
PLAY
( ) and
STOP
( ) (see page 11).
Advanced controls
These buttons are described on the facing page.
0–9 keypad
This allows direct access to individual tracks on audio CDs. To
select a track, press the corresponding keypad button followed
by
select a track, press the corresponding keypad button followed
by
OK
. For tracks greater than 9, enter the digits in sequence. For
example, to play track 15, press
1
, then
5
, then
OK
.
CD/DVD
Ensure that DVD mode is selected using the
CD/DVD
toggle
button. The ‘DVD’ LED above the
CD/DVD
button is lit briefly
when DVD mode is selected.
DISP (display)
Dims or turns the DV27’s display on or off. Turning the display off
generally gives a slight improvement in sound quality.
generally gives a slight improvement in sound quality.
Pressing
DISP
once turns the display off; twice dims the display. To
restore the display to full brightness, press
DISP
a third time.
A–B
This button enables you to repeat a selected
section from the disc (see page 14).
section from the disc (see page 14).
RPT (repeat)
Press
RPT
to cycle through the repeat play options.
Fast play and Skip chapter/tracks
Play fast (
) and Skip ( ) chapters/tracks in both
directions (see page 11).
Standby
Press
STANDBY
to toggle the standby state of the DVD player.
Note that Arcam CD players are not controlled by this button.
CLEAR
Use
CLEAR
within the ‘Program’ and ‘Bookmark’ menus to clear
a numeric field (see pages 14–15).
PROG (program)
You can program a selection of up to 20 chapters/tracks from a
disc to play in any order. Press
disc to play in any order. Press
PROG
to access the ’Programme’
menu (see pages 15 and 17).
Slow play
Press or on the remote control to play slow forward or
backwards. There are four speeds of slow playback: 1/5, 1/4,
1/3 and 1/2. Press the button repeatedly to cycle through the
different speeds. To resume normal playback speed, press
backwards. There are four speeds of slow playback: 1/5, 1/4,
1/3 and 1/2. Press the button repeatedly to cycle through the
different speeds. To resume normal playback speed, press
PLAY
.
Note that slow play does not apply to audio CDs.
Cursor pad and OK button
Use the cursor pad to navigate the On Screen Display (OSD)
and menu pages. Confirm your selection with the
and menu pages. Confirm your selection with the
OK
button.