ATIKA asp 5,5 Brochure
The electrical connection or repairs to electrical parts
of the machine must be carried out by a certified
electrician or one of our customer service points. Local
regulations – especially regarding protective measures
– must be observed.
electrician or one of our customer service points. Local
regulations – especially regarding protective measures
– must be observed.
17
Repairs to other parts of the machine must be carried
out by the manufacturer or one of his customer service
points.
points.
Use only original spare parts. Accidents can arise for
the user through the use of other spare parts. The
manufacturer is not liable for any damage or injury
resulting from such action.
manufacturer is not liable for any damage or injury
resulting from such action.
T
T
r
r
a
a
n
n
s
s
p
p
o
o
r
r
t
t
I
I
n
n
s
s
t
t
r
r
u
u
c
c
t
t
i
i
o
o
n
n
s
s
Move the splitting blade right down every time before
the machine is transported.
To transport the
machine, grasp the
strap one hand and tilt
the log splitter slightly
towards you. The log
splitter can be easily
transported in this
position.
machine, grasp the
strap one hand and tilt
the log splitter slightly
towards you. The log
splitter can be easily
transported in this
position.
To avoid the escape of
oil during the transport
the oil dipstick must be
replaced by the
transport closure.
oil during the transport
the oil dipstick must be
replaced by the
transport closure.
P
P
o
o
s
s
i
i
t
t
i
i
o
o
n
n
i
i
n
n
g
g
Place chocks under the wheels to prevent the machine rolling
during operation.
Ensure that the working area meets the following conditions:
during operation.
Ensure that the working area meets the following conditions:
− no danger of slipping
− level
− free of obstacles
− sufficiently well lit
Do not operate the machine in the direct vicinity of gas or
petrol pipes or containers, or any other easily inflammable
materials.
petrol pipes or containers, or any other easily inflammable
materials.
S
S
t
t
a
a
r
r
t
t
-
-
u
u
p
p
Check that the machine is completely and correctly
assembled.
assembled.
Before using the log splitter, make sure each time that
−
there are no faulty connections (tears, cuts, etc.)
−
there are no damage at the machine
−
all screws are tight
−
check the hydraulic system for any possible leaks
−
the oil level
The transport
closure with gasket
must be replaced
before the initiation
by the oil dipstick.
closure with gasket
must be replaced
before the initiation
by the oil dipstick.
6
transport closure
L
Mains connection
Compare the voltage given on the machine model plate
e.g. 230 V with the mains voltage and connect the
machine to the relevant and properly earthed plug.
e.g. 230 V with the mains voltage and connect the
machine to the relevant and properly earthed plug.
Only use connection cables with sufficient diameters.
5
Connect the machine via a 30 mA fault current safety
switch.
switch.
Transport belt
L
Fuse protection
230
V~
Î
16 A inert
400 V 3~ Î 16 A
L
Switching on / off
Prior to every use, check the function of the
disconnection mechanism (by switching on and off).
Do not use any device where the switch can not be
switched on and off. Damaged switches must be
repaired or replaced immediately by the customer
service.
switched on and off. Damaged switches must be
repaired or replaced immediately by the customer
service.
Switching on
Press the green
button.
button.
Switching off
Press the red
button.
button.
7
L
Lock in case of power (zero-voltage
initiator)
The equipment will switch off automatically if there is a power
cut. Repress the green button to switch it on again.
cut. Repress the green button to switch it on again.