Canon pixma mp600 User Manual

Page of 2
Start Here
Easy Setup Instructions
Turn the Easy-Scroll Wheel 
left or right to easily select 
a menu or a setting item. 
For details, refer to “Basic 
Operation for the Operation 
Panel” in the Quick Start 
Guide.
* You can also use the 
{
}
[
, or 
]
 button to 
select.
Cassette
Easy-Scroll Wheel
For information on how to load paper in the 
Cassette, refer to “Loading Paper in the 
Cassette” in “Loading Printing Paper” of the 
Quick Start Guide
.
Unpack the Machine
QT5-0683-V02
Hardware setup and Print Head 
alignment is complete.
a
 Place the machine on a flat and 
horizontal surface, and do not place 
any objects in front of the machine. 
Open the Sheet Feeder Cover and 
pull the Paper Support, then the Paper 
Output Tray and open the Output Tray 
Extension.
 Caution
Before turning on the machine, remove all of the 
shipping tapes.
 Important
Do not connect the USB cable until after the soft-
ware is installed.
 Note
To open the Paper Output Tray, put your finger in the 
rounded indent of the tray and open it gently.
Plug the power cord in the back of the 
machine and connect the other end to 
the wall outlet.
 Important
Make sure that the Document Cover is closed.
Open the Operation Panel, then press 
the 
ON/OFF button to turn on the 
machine.
1
  Prepare the Machine
2
  Install the Print Head
3
  Install the Ink Tanks
4
  Align the Print Head
d
 Use the { or } button on the 
Operation Panel to select the language 
for the LCD, then press the 
OK button. 
(1)  Press the { or } 
button to select the 
language.
(2)  Press the 
OK 
button.
 Important
If an unintended language is displayed on the 
LCD, press the Back button to return to the Lan-
guage selection screen.
Once the message “
Install the print head and 
set the ink tank.” appears, go to 
e
.
Open the Scanning Unit (Printer Cover) 
until it locks into place. The Print Head 
Holder moves to the center.
Scanning Unit (Printer Cover)
 Important
For your safety, always firmly grip the areas il-
lustrated when opening the Scanning Unit (Printer 
Cover).
Open the Inner Cover. Write down 
the serial number located inside the 
machine. You will need this to register 
your product.
Inner Cover
Serial Number Location
Remove the Print Head from its 
package.
 Caution
There may be some transparent or light blue ink 
on the inside of the bag the print head comes in, 
or the inside of the protective cap - this has no 
effect on print quality. Be careful not to get ink on 
yourself when handling these items.
Remove the orange protective cap from 
the Print Head and discard it.
Protective Cap
Print Head Nozzles
Electrical Contacts
 Note
Do not touch the print head nozzles or the electrical 
contacts.
Firmly raise the Print Head Lock Lever 
until it stops.The Print Head Lock Lever 
may feel heavy.
Insert the Print Head.
Do not touch!
Lower the Print Head Lock Lever 
carefully.
 Important
If the Scanning Unit (Printer Cover) is left open 
for more than 10 minutes, the Print Head Holder 
moves to the right. Close and reopen the Scanning 
Unit (Printer Cover) to return the Holder to the 
center.
Peel back the orange tab completely 
and remove the plastic wrapper from 
the ink tank.
If the orange-colored protective film is not removed 
completely, problems with printing may occur.
Twist off and discard the orange 
protective cap located on the bottom of 
the ink tank.
Electrical Contacts
Ink Port
Protective Cap
Do not press!
 Important
• Do not touch the electrical contacts.
• Do not touch the ink port.
Insert the ink tank into the right-hand 
slot and press the   mark on the ink 
tank until it clicks into place.
Make sure the ink lamp lights red.
Refer to the color 
guide on the Print 
Head Lock Lever.
Close the Inner Cover and the 
Scanning Unit (Printer Cover).
 Important
• For your safety, always firmly grip the areas il-
lustrated when closing the Scanning Unit (Printer 
Cover).
• The machine starts operating. Wait about 2 min-
utes until the machine stops making noise.
Pinch the Paper Guide and slide it to 
the left end.
Paper Support
Extension
Paper Guide
Load a sheet of letter- or A4-sized 
blank paper in the Auto Sheet Feeder, 
align the paper with the right side of 
the Cover Guide, then slide the Paper 
Guide against the paper stack.
Paper Guide
Cover Guide
Print Side
Make sure that 
Yes is selected in the 
message requesting head alignment, 
then press the 
OK button.
 Note
Print Head alignment takes about 6 minutes to 
complete. Do not start another operation here.
The pattern is printed. And Print Head is aligned 
automatically.
OK
 Note
• The pattern is printed in black and blue.
• When Automatic Print Head Alignment cannot be 
executed correctly, the message “
Auto head align 
has failed.” is displayed on the LCD. Refer to “Error 
Message is Displayed on the LCD” in the User’s 
Guide 
on-screen manual.
Photo All-in-One
• Please confirm the included items against the illustration printed on the lid of the packing box.
• A USB cable is necessary to connect the machine with your computer.