Canon pixma mp600 Quick Setup Guide
70
Troubleshooting
LCD Cannot Be Seen At All
An Unintended Language Is Displayed on the LCD
“The remaining level of the following ink
cannot be correctly detected. Replace
the ink tank.”
U130
cannot be correctly detected. Replace
the ink tank.”
U130
The remaining ink level cannot be correctly detected.
Replace the ink tank and close the Scanning Unit (Printer Cover).
Printing with an ink tank that was once empty may damage the machine.
If you want to continue printing in this condition, you need to release the function
for detecting the remaining ink level. Press and hold the Stop/Reset button for
at least 5 seconds, and then release it.
* With this operation, releasing the function for detecting the remaining ink
Replace the ink tank and close the Scanning Unit (Printer Cover).
Printing with an ink tank that was once empty may damage the machine.
If you want to continue printing in this condition, you need to release the function
for detecting the remaining ink level. Press and hold the Stop/Reset button for
at least 5 seconds, and then release it.
* With this operation, releasing the function for detecting the remaining ink
level is memorized. Please be advised that Canon shall not be liable for any
machine malfunction or damage caused by refilled ink tanks.
See “Replacing an Ink Tank” on page 46.
machine malfunction or damage caused by refilled ink tanks.
See “Replacing an Ink Tank” on page 46.
“The following ink tank cannot be
recognized.”
U140
U150
recognized.”
U140
U150
z
The ink tank is not compatible with this machine. (The lamp on the ink tank is
off.)
Install an appropriate ink tank.
See “Replacing an Ink Tank” on page 46.
off.)
Install an appropriate ink tank.
See “Replacing an Ink Tank” on page 46.
z
An Ink tank error has occurred. (The lamp on the ink tank is off.)
Replace the ink tank.
See “Replacing an Ink Tank” on page 46.
Replace the ink tank.
See “Replacing an Ink Tank” on page 46.
“****
Error code”
Error code”
Turn off the machine, and unplug the power cord of the machine from the power
supply. After a while, plug the power cord of the machine back in, and then turn
on the machine. If the same error occurs, contact a Canon service
representative.
supply. After a while, plug the power cord of the machine back in, and then turn
on the machine. If the same error occurs, contact a Canon service
representative.
“Scanner is not operating correctly.”
Turn off the machine, and unplug the power cord of the machine from the power
supply. After a while, plug the power cord of the machine back in, and then turn
on the machine. If the same error occurs, contact a Canon service
representative.
supply. After a while, plug the power cord of the machine back in, and then turn
on the machine. If the same error occurs, contact a Canon service
representative.
Cause
Action
Cannot see the display on the LCD.
z
If the POWER lamp is off
The machine is not powered on. Connect the power cord and press the ON/
OFF button. The machine will power on and the LCD will display a message.
The machine is not powered on. Connect the power cord and press the ON/
OFF button. The machine will power on and the LCD will display a message.
z
If the POWER lamp is lit
The LCD may be in the screen-saver mode. On the Operation Panel, press a
button other than the ON/OFF button.
The LCD may be in the screen-saver mode. On the Operation Panel, press a
button other than the ON/OFF button.
Cause
Action
The language you want to be displayed
is not selected.
is not selected.
Select the language you want to be displayed according to the following
procedure.
(1)Press the HOME button. Wait for about 5 seconds, select
procedure.
(1)Press the HOME button. Wait for about 5 seconds, select
, and then
press the OK button.
(2)Press the ] button to select
, then press the OK button.
(3)Press the } button four times, then press the OK button.
If the Bluetooth unit is connected to the machine, press the } button five
times, and then press the OK button.
times, and then press the OK button.
(4)Press the { or } button to select the language you want to be displayed,
then press the OK button.
Message
Action