Nikon FAA350NA User Manual
34
Film
•
Setting and confirming film speed
Rotate the Main-Command Dial while pressing the film
speed ° button to set film speed in use.
speed ° button to set film speed in use.
• Film speed can be set to s and between ISO 6-6400 in 1/3 steps by rotating
the Main-Command Dial.
• When film speed is set to s and DX-coded film is installed, film speed is
automatically set between ISO 25-5000. Film speed can also be set manually
with DX-coded film to have an effect of increased or decreased film sensitivity.
with DX-coded film to have an effect of increased or decreased film sensitivity.
• Film speed can be set between ISO 6-6400 with non-DX-coded film.
• Press the ° button to confirm the film speed set on the camera.
• Press the ° button to confirm the film speed set on the camera.
·
5
: When film speed is set to s and non-DX-coded film is loaded, a, s
and Err blink in the LCD panel after film is advanced to the first frame. This
warning indication can be changed to appear when the power switch is turned
on (page 71).
warning indication can be changed to appear when the power switch is turned
on (page 71).
•
Mid-roll rewind
To rewind film at mid-roll, press the two film rewind
buttons „ simultaneously for approx. 1 sec.
buttons „ simultaneously for approx. 1 sec.
• o–– blinks in the LCD panel during film rewind and the frame counter counts
backwards until rewind is complete.
• Film is completely rewound when the frame counter shows blinking “E”. (E
appears without blinking when the exposure meter is off.) Open the camera
back and remove the film cartridge.
back and remove the film cartridge.
•
If film does not start to rewind or film rewind stops at mid-roll
• When battery power is very low, or at low temperatures, film may not start
rewinding or film rewind may stop at mid-roll, and o–– and frame number will
blink in the LCD panel. In this case, turn the power switch off, change
batteries, then turn the power switch on and rewind film again.
blink in the LCD panel. In this case, turn the power switch off, change
batteries, then turn the power switch on and rewind film again.
•
Film advance mode
Rotate the film advance mode selector while pressing
the film advance mode selector lock release to select
film advance mode.
the film advance mode selector lock release to select
film advance mode.
• The following film advance modes are available:
S:
Single-frame shooting
Fully depressing the shutter release button takes one picture and
automatically advances the film by one frame.
Fully depressing the shutter release button takes one picture and
automatically advances the film by one frame.
C:
Continuous shooting
Shots are taken continuously at the rate of up to approx. 4.5 fps as long
as you keep the shutter release button fully depressed.
Shots are taken continuously at the rate of up to approx. 4.5 fps as long
as you keep the shutter release button fully depressed.
Cs: Continuous silent-low-speed shooting
Shots are taken continuously at the rate of up to approx. 3 fps as long as
you keep the shutter release button fully depressed. Film rewind speed
also slows down and there is little rewind noise.
you keep the shutter release button fully depressed. Film rewind speed
also slows down and there is little rewind noise.
Film advance speed is tested using camera settings of focus mode C, exposure
mode ¢, shutter speed 1/250 sec. or faster, aperture other than maximum, at
normal temperature of 20°C (68°F), with AA-type alkaline-manganese batteries, for
the first to 36th frames of a film.
mode ¢, shutter speed 1/250 sec. or faster, aperture other than maximum, at
normal temperature of 20°C (68°F), with AA-type alkaline-manganese batteries, for
the first to 36th frames of a film.
• When the film advance mode selector is set to Z, multiple exposure can be
performed (page 60). Also, when it is set to V, self-timer operation can be
performed (page 67).
performed (page 67).
• When the batteries are exhausted, film advance speed slows down since film
advance automatically switches to start after the mirror is all the way down.
(Normally, film advance starts immediately when the mirror starts to go down.)
In this case, battery change is recommended.
(Normally, film advance starts immediately when the mirror starts to go down.)
In this case, battery change is recommended.
Film
35
P500 (E) 02.12.27 5:48 PM Page 34
WWW.LENSINC.NET