Sony 6557-03n, 03s,43n,43s ibm chassis n3 Service Manual
1-2
4
Getting Started
to a power outlet
to AC IN
Power cord
Setup
This monitor works with platforms running at horizontal
frequencies between 30 and 94 kHz.
frequencies between 30 and 94 kHz.
Step 1: Connect the monitor to the
computer
With the computer switched off, connect the video signal
cable to the video output of the computer.
cable to the video output of the computer.
Note
Do not short the pins of the video signal cable.
Do not short the pins of the video signal cable.
Step 2: Connect the power cord
With the monitor switched off, connect one end of the
proper power cord for your local supply to the monitor and
the other end to a power outlet.
proper power cord for your local supply to the monitor and
the other end to a power outlet.
Step 3: Turn on the monitor and computer
The installation of your monitor is complete.
Note
If “OUT OF SCAN RANGE” or “NO INPUT SIGNAL” appears on
the screen, see “Warning Messages” on page 16.
If “OUT OF SCAN RANGE” or “NO INPUT SIGNAL” appears on
the screen, see “Warning Messages” on page 16.
to a computer with
an HD15 video output
an HD15 video output
to a computer with
a 13W3 video output
a 13W3 video output
9 Video input 2 connector (13W3 cable)
Inputs RGB video signal (0.700 Vp-p, positive).
*
Pins serve a dual purpose as combined sync input and as H.sync
input if V.Sync is present on pin no. 9.
input if V.Sync is present on pin no. 9.
** Display Data Channel (DDC) Standard by VESA
Note
If you use a computer or video board of high output level (about 1.0
Vp-p), you may not be able to obtain the optimum display. In such
case, try decreasing the picture contrast, or use a computer or video
board with a lower output level.
If you use a computer or video board of high output level (about 1.0
Vp-p), you may not be able to obtain the optimum display. In such
case, try decreasing the picture contrast, or use a computer or video
board with a lower output level.
Pin No.
A1
A2
A3
1
2
3
Signal
Ground
C.Sync*
––
Bi-Directional
Data (SDA)**
Data (SDA)**
DDC + 5V**
V.Sync
Ground
Signal
Red Video &
Ground
Ground
Green Video &
Ground
Ground
Blue Video &
Ground
Ground
––
Data Clock
(SCL)**
(SCL)**
––
(13W3)
(HD15)
(13W3)
(HD15)
Pin No.
4
5
6
7
8
9
10
A1
A2
A3
1
2
3
4
5
6
7
8
9 10
5
Getting Started
Getting Started
F
EN
ES
C
Automatically Adjusting the Size
and Centering of the Picture
and Centering of the Picture
By pressing the
button, the size and centering of the
picture are automatically adjusted to fit the screen.
1
Turn on the monitor and computer.
2
Press the
button.
The picture is adjusted to fit the center of the screen.
Notes
• This function is intended for use with a computer running
• This function is intended for use with a computer running
graphic user interface software that provides a full-screen
picture. It may not work properly if the background color is
dark or if the input picture does not fill the screen to the edges.
picture. It may not work properly if the background color is
dark or if the input picture does not fill the screen to the edges.
• The screen may go blank for a few seconds while performing the
auto-sizing function. This is not a malfunction.
• Although the signals for picture aspect ratio 5:4 (resolution: 1280
×
1024) do not fill the screen to the edges, the picture is
accurately displayed.
Selecting the On-screen Display
Language
Language
If you need to change the OSD language, see “Using the
LANG (Language) On-screen Display” on page 14.
The default setting is English.
LANG (Language) On-screen Display” on page 14.
The default setting is English.
Selecting the Input Signal
This monitor has two signal input connectors (HD15 and
13W3) and can be connected to two computers
simultaneously. Select the input signal you want to view as
follows.
13W3) and can be connected to two computers
simultaneously. Select the input signal you want to view as
follows.
1
Turn on the monitor and both computers.
2
Press the
button.
The MENU OSD appears.
3
Press the ¨./> and >?// buttons to select “
OPTION,” and press the
OPTION,” and press the
button again.
The OPTION OSD appears.
4
Press the ¨./> buttons to select “
(INPUT).”
MENU
EXIT
CENTER
SIZE
GEOM
COLOR
LANG
ZOOM
SCREEN
OPTION
OK
MENU
ON
MANUAL DEGAUSS
UNLOCK
1 MIN
OPTION
ZZ...
1
ZZ...
INPUT
1 MIN
OPTION
UNLOCK
2
(continued)