Sony CDP-XE220 User Manual
Additional Information
18
GB
Specifications
Compact disc player
Laser
Semiconductor laser (
λ
= 780 nm)
Emission duration: continuous
Laser output
Max 44.6
µ
W*
* This output is the value measured at
a distance of 200 mm from the
objective lens surface on the Optical
Pick-up block with 7 mm aperture.
objective lens surface on the Optical
Pick-up block with 7 mm aperture.
Frequency response
2 Hz to 20 kHz ± 0.5 dB
Signal-to-noise ratio
More than 100 dB
Dynamic range
CDP-XE520: More than 98 dB
CDP-XE320 and CDP-XE220:
More than 92 dB
Harmonic distortion
CDP-XE520: Less than 0.0045%
CDP-XE320 and CDP-XE220:
Less than 0.005%
Channel separation
More than 95 dB
Outputs
LINE OUT
DIGITAL
OUT
(OPTICAL)
OUT
(OPTICAL)
PHONES
(CDP-XE520
only)
(CDP-XE520
only)
General
Power requirements
220 V – 230 V AC, 50/60 Hz
Power consumption
CDP-XE520: 11 W
CDP-XE320/XE220: 10 W
Dimensions (approx.)
430
×
95
×
290 mm
(w/h/d)
(17
×
3 3/4
×
11 1/2 in.) incl. projecting
parts
Mass (approx.)
CDP-XE520: 3.2 kg (7 lbs 1 oz)
CDP-XE320/XE220: 3.0 kg (6 lbs 10 oz)
Supplied accessories
Audio cord (2 phono plugs – 2 phono plugs) (1)
Remote commander (remote) (CDP-XE520 and
CDP-XE320 only) (1)
Sony SUM-3 (NS) batteries (CDP-XE520 and CDP-XE320
only) (2)
Remote commander (remote) (CDP-XE520 and
CDP-XE320 only) (1)
Sony SUM-3 (NS) batteries (CDP-XE520 and CDP-XE320
only) (2)
Design and specifications are subject to change without notice.
Load
impedance
impedance
Over 10 kilohms
Wave length: 660 nm
32 ohms
Jack
type
type
Phono
jacks
jacks
Optical
output
connector
output
connector
Stereo
phone
jack
phone
jack
Maximum
output
level
output
level
2 V
(at 50 kilohms)
(at 50 kilohms)
–18 dBm
10 mW
Troubleshooting
If you experience any of the following difficulties while
using the player, use this troubleshooting guide to help
you remedy the problem. Should any problem persist,
consult your nearest Sony dealer.
using the player, use this troubleshooting guide to help
you remedy the problem. Should any problem persist,
consult your nearest Sony dealer.
There’s no sound.
/ Check that the player is connected securely.
/ Make sure you operate the amplifier correctly.
/ Adjust the output level with LINE OUT LEVEL +/–
/ Make sure you operate the amplifier correctly.
/ Adjust the output level with LINE OUT LEVEL +/–
on the remote (CDP-XE520 and CDP-XE320 only).
The CD does not play.
/ There’s no CD inside the player. “- NO DISC -” (or
“no dISC” for the CDP-XE320 and CDP-XE220)
appears. Insert a CD.
appears. Insert a CD.
/ Place the CD with the label side up on the disc tray
correctly.
/ Clean the CD (see page 17).
/ Moisture has condensed inside the player. Remove
/ Moisture has condensed inside the player. Remove
the disc and leave the player turned on for about an
hour (see page 2).
hour (see page 2).
The recording level has changed (CDP-XE520 and
CDP-XE320 only).
CDP-XE320 only).
/ The recording level changes if you adjust the output
level with LINE OUT LEVEL +/– on the remote
during recording.
during recording.
The remote does not function (CDP-XE520 and CDP-XE320
only).
only).
/ Remove the obstacles in the path of the remote and
the player.
/ Point the remote at the remote sensor g on the player.
/ Replace all the batteries in the remote with new ones
/ Replace all the batteries in the remote with new ones
if they are weak.