Sony CDX-FW500 User Manual
17
When an MP3 file is played, you can select an
album using the rotary commander.
album using the rotary commander.
(With optional unit)
*1
Only if the corresponding optional equipment is
connected.
connected.
*2
If your car has no ACC (accessory) position on the
ignition key switch, after turning off the ignition, be
sure to press and hold
ignition key switch, after turning off the ignition, be
sure to press and hold
(OFF)
until the display
disappears.
*3
Available only when an optional CD unit with the
MP3 file control function is connected, and MP3 file
is played.
MP3 file control function is connected, and MP3 file
is played.
Changing the operative direction
The operative direction of controls is factory-set
as shown below.
as shown below.
If you need to mount the rotary commander on
the right hand side of the steering column, you
can reverse the operative direction.
the right hand side of the steering column, you
can reverse the operative direction.
Press
(SEL)
for 2 seconds while
pushing the VOL control.
Adjusting the sound
characteristics
characteristics
You can adjust the balance, fader, low pass filter
and subwoofer volume.
and subwoofer volume.
1
Press the select button repeatedly
until “BAL,” “FAD,” “LPF” or “SUB”
appears.
until “BAL,” “FAD,” “LPF” or “SUB”
appears.
Each time you press the select button, the
item changes as follows:
item changes as follows:
LOW
*
1
t
MID
*
1
t
HI
*
1
t
BAL (left-right)
t
FAD (front-rear)
t
LPF (low pass filter)
*
2
*
3
t
SUB (subwoofer volume)
*
2
*
4
*1
When EQ3 is activated (page 19).
*2
When “SUB” is selected (page 18).
*3
The cut off frequency is adjustable to 78 Hz,
125 Hz or OFF.
125 Hz or OFF.
*4
The volume level is adjustable between –10
and +10 steps. (Below –10, “ATT” is displayed.)
and +10 steps. (Below –10, “ATT” is displayed.)
2
Rotate the volume control dial to
adjust the selected item.
adjust the selected item.
Note
Adjust within 3 seconds after selecting the item.
Adjust within 3 seconds after selecting the item.
Quickly attenuating the
sound
sound
(With the rotary commander or the card
remote commander)
remote commander)
Press
(ATT)
.
After “ATT-ON” momentarily appears,
“ATT” appears in the display.
“ATT” appears in the display.
To restore the previous volume level, press
(ATT) again.
(ATT) again.
Tip
When the interface cable of a car telephone is
connected to the ATT lead, the unit decreases the
volume automatically when a telephone call comes in
(Telephone ATT function).
When the interface cable of a car telephone is
connected to the ATT lead, the unit decreases the
volume automatically when a telephone call comes in
(Telephone ATT function).
To
Do this
Skip discs
– Disc selection
– Disc selection
Push in and rotate [once for
each disc] the control.
To continuously skip discs,
push in and rotate once and
rotate again within 2
seconds (and hold) the
control.
each disc] the control.
To continuously skip discs,
push in and rotate once and
rotate again within 2
seconds (and hold) the
control.
Skip albums*
3
– Album selection
1
To enter Album selection
mode, push in, then rotate
and hold the control.
Within 2 seconds,
proceed to step 2.
mode, push in, then rotate
and hold the control.
Within 2 seconds,
proceed to step 2.
2
Push in, then rotate
quickly and repeatedly, to
skip albums one by one.
quickly and repeatedly, to
skip albums one by one.
To increase
To decrease