Sony CDX-V7800X User Manual
Installation/Connections
Instalación/Conexiones
ƒw‚¸¡ ‰u‚ ‡s–
Sony Corporation © 2000
Printed in Korea
CDX-V7800X
FM/AM
Multi Media
Player
Multi Media
Player
3-049-998-11
(1)
1
×
4
×
2
2
3
4
5
6
7
8
Equipment used in illustrations (not supplied)
Equipo utilizado en las ilustraciones (no suministrado)
Equipo utilizado en las ilustraciones (no suministrado)
·¡„ˇ⁄⁄“”‚¸‚m¡]«D“
e¡^
Rear speaker
Altavoz trasero
Altavoz trasero
«Æ·›`n „
Front speaker
Altavoz delantero
Altavoz delantero
«e·›`n „
AUDIO OUT
REAR
AUDIO OUT
FRONT
VIDEO OUT
Parts Iist (1)
The numbers in the list are keyed to those in the
instructions.
instructions.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
your fingers.
Cautions
• This unit is designed for negative ground 12 V
DC operation only.
• Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
• Before making connections, disconnect the
ground terminal of the car battery to avoid
short circuits.
short circuits.
• Connect the yellow and red power input leads
only after all other leads have been connected.
• Run all ground wires to a common ground
point.
• Be sure to insulate any loose unconnected
wires with electrical tape for safety.
Notes on the power supply cord (yellow)
• When connecting this unit in combination with
• When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
circuit’s rating must be higher than the sum of
each component’s fuse.
• When no car circuits are rated high enough,
connect the unit directly to the battery.
Connection example (2)
Notes (2-B)
• Be sure to connect the ground cord before
• Be sure to connect the ground cord before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
be deactivated.
Connection diagram (3)
1
To a metal surface of the car
First connect the black ground lead, then
connect the yellow and red power input leads.
First connect the black ground lead, then
connect the yellow and red power input leads.
1
2
A
B
2
To the parking brake switch cord
Be sure to connect the parking cord (light green)
to the parking brake switch cord. The mounting
position of the parking brake switch cord
depends on your car. Refer to the system
connection diagram below and consult your car
dealer or your nearest Sony dealer for further
details.
Be sure to connect the parking cord (light green)
to the parking brake switch cord. The mounting
position of the parking brake switch cord
depends on your car. Refer to the system
connection diagram below and consult your car
dealer or your nearest Sony dealer for further
details.
3
To the power aerial control lead or power
supply lead of aerial booster amplifier
Notes
• It is not necessary to connect this lead if there
supply lead of aerial booster amplifier
Notes
• It is not necessary to connect this lead if there
is no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
manually-operated telescopic aerial.
• When your car has a built-in FM/AM aerial in
the rear/side glass, see “Notes on the control
and power supply leads.”
and power supply leads.”
4
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
5
To the interface cable of a car telephone
6
To the +12 V power terminal which is energised
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black ground to it first.
energised at all times.
Be sure to connect the black ground to it first.
• When your car has a built-in FM/AM aerial in
the rear/side glass, see “Notes on the control
and power supply leads.”
and power supply leads.”
7
To the +12 V power terminal which is energised
at all times
Be sure to connect the black ground to it first.
at all times
Be sure to connect the black ground to it first.
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V
• The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM aerial in the
rear/side glass, connect the power aerial control
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing aerial
booster. For details, consult your dealer.
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing aerial
booster. For details, consult your dealer.
• A power aerial without relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
speakers with those of the left speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
terminals may damage the unit.
Mobile colour TV
TV móvil en color
TV móvil en color
¤T¤fi–mƒ „q ł
Rotary commander RM-X4S
Mando rotativo RM-X4S
Mando rotativo RM-X4S
– ´ ƒ¡––¤
„
RM-X4S
Power amplifier
Amplificador de potencia
Amplificador de potencia
¥\†v'æ⁄j „