Sony CDX-S2210X User Manual
15
• Lead-free solder is used for soldering certain parts.
(more than 80 %)
• Halogenated flame retardants are not used in the
certain printed wiring boards.
• Halogenated flame retardants are not used in
cabinets.
• VOC (Volatile Organic Compound)-free vegetable oil
based ink is used for printing the carton. (CDX-
S2210X and CDX-S2210S only)
S2210X and CDX-S2210S only)
• Packaging cushions do not use polystyrene foam.
Troubleshooting
The following checklist will help you remedy
problems you may encounter with your unit.
Before going through the checklist below, check
the connection and operating procedures.
problems you may encounter with your unit.
Before going through the checklist below, check
the connection and operating procedures.
General
No power is being supplied to the unit.
• Check the connection. If everything is in order,
check the fuse.
• If the unit is turned off and the display
disappears, it cannot be operated with the
remote commander.
t Turn on the unit.
remote commander.
t Turn on the unit.
The power aerial does not extend.
The power aerial does not have a relay box.
No sound.
• The volume is too low.
• The ATT function is activated.
• The position of the fader control (FAD) is not
• The ATT function is activated.
• The position of the fader control (FAD) is not
set for a 2-speaker system.
No beep sound.
• The beep sound is cancelled (page 9).
• An optional power amplifier is connected and
• An optional power amplifier is connected and
you are not using the built-in amplifier.
The contents of the memory have been
erased.
erased.
• The RESET button has been pressed.
t Store again into the memory.
• The power connecting lead or battery has been
disconnected.
• The power connecting lead is not connected
properly.
Stored stations and correct time are erased.
The fuse has blown.
Makes noise when the position of the
ignition key is switched.
The fuse has blown.
Makes noise when the position of the
ignition key is switched.
The leads are not matched correctly with the
car’s accessory power connector.
car’s accessory power connector.
The display disappears from/does not
appear in the display window.
appear in the display window.
• The dimmer is set “DIM-ON” (page 9).
• The display disappears if you press and hold
• The display disappears if you press and hold
(OFF).
t Press and hold (OFF) again until the
t Press and hold (OFF) again until the
display appears.
• The connectors are dirty (page 13).
CD playback
The disc cannot be loaded.
• Another disc is already loaded.
• The disc has been forcibly inserted upside
• The disc has been forcibly inserted upside
down or in the wrong way.
The disc does not playback.
• Defective or dirty disc.
• The CD-Rs/CD-RWs are not for audio use
• The CD-Rs/CD-RWs are not for audio use
MP3 files cannot be played back.
The disc is not corresponding to the MP3 format
and version (page 12).
and version (page 12).
MP3 files take longer to play back than
others.
others.
The following discs take a longer time to start
playback.
– a disc recorded with a complicated tree
playback.
– a disc recorded with a complicated tree
structure.
– a disc recorded in Multi Session.
– a disc to which data can be added.
– a disc to which data can be added.
The ATRAC CD cannot play.
• The disc is not created by authorized software,
such as SonicStage or SonicStage Simple
Burner.
Burner.
• Tracks that are not included in the group cannot
be played.
The display items do not scroll.
• For discs with very many characters, those may
not scroll.
• “A.SCRL” is set to off.
t Set “A.SCRL-ON” (page 9) or press
(SCRL) on the card remote commander.
The sound skips.
• Installation is not correct.
t Install the unit at an angle of less than
45° in a sturdy part of the car.
• Defective or dirty disc.
The operation buttons do not function.
The disc will not eject.
The disc will not eject.
Press the RESET button (page 4).
continue to next page
t