Sony HDW-S2000 User Manual
Chapter 6
Shot Mark Function
6-8
Chapter 6
Shot Mark Function
Cuing up to shot marks adjacent to the
current tape position (index function)
current tape position (index function)
1
In item G01 of the shot mark operation menu
(page 6-3), select one of recording start mark, shot
mark 1, shot mark 2, and post mark, or select all.
(page 6-3), select one of recording start mark, shot
mark 1, shot mark 2, and post mark, or select all.
2
Holding down the MARK button, press the F FWD
button or REW button.
button or REW button.
While the tape is moving, the F FWD button or
REW button flashes.
REW button flashes.
When the shot mark is detected, its type is displayed in
time data display area 2 (page 2-9) on the lower
control panel and in the character information display
on the monitor screen.
time data display area 2 (page 2-9) on the lower
control panel and in the character information display
on the monitor screen.
For details of character information display on the monitor
screen, see F4 (CHARA) in function menu page 4 (page 9-7)
and setup menu item 005 (page 10-7).
screen, see F4 (CHARA) in function menu page 4 (page 9-7)
and setup menu item 005 (page 10-7).
Note
You cannot use the above procedure to cue up to a
virtual shot mark.
virtual shot mark.
6-3-5 Reading In Shot Data
When there is shot data (time, device, and other
information about the shooting) written on the tape,
you can read it in and display it on the monitor.
information about the shooting) written on the tape,
you can read it in and display it on the monitor.
Displaying the shot data
Holding down the ENTRY button, press the PLAY
button.
button.
Z
ENTRY button
PLAY button
The tape is played back, and the shot data displayed.
To delete the shot data
Once again hold down the ENTRY button, and press
the PLAY button.
Once again hold down the ENTRY button, and press
the PLAY button.
Example of shot data display
The shot data display appears as shown below.
The details in the shot data depend on the shooting
conditions. If because of the devices used there is no
shot data on a part of the tape, it appears as blank.
conditions. If because of the devices used there is no
shot data on a part of the tape, it appears as blank.
Displaying the shot data on the shot mark
list
list
Turn the MULTI CONTROL knob to position the
cursor on a separator in the shot mark list.
If there is shot data recorded when the immediately
following shot mark was written, it appears in the
display as shown below.
cursor on a separator in the shot mark list.
If there is shot data recorded when the immediately
following shot mark was written, it appears in the
display as shown below.
You can sort the shot marks in the list, based on the shot
data. For details, see the next section.
data. For details, see the next section.
Camera IDs
SERIAL NUMBER 010001
DATE 1998.05.11
DATE 1998.05.11
MODEL NAME DNW 0090
TIME 12.55.10
CASSETTE NUMBER 0095
CASSETTE NUMBER 0095
ID1 AAAAAAAAAAAA
SHOT NUMBER 0052
ID2 BBBBBBBBBBBB
ID3 CCCCCCCCCCCC
ID4 DDDDDDDDDDDD
ID3 CCCCCCCCCCCC
ID4 DDDDDDDDDDDD
TCR 23:59:59:29
Recording
time code
time code
First shot
mark in the
group
mark in the
group
NO. TIME CODE
(---/180)
SHOT MARK
*012345-DNW_-0123-4567-
011 S1 10:04:05:11
011 S1 10:04:05:11
013 V 10:07:05:02
012 R 10:05:35:24
----------------------------
014 R 10:08:35:04
015 S2 10:09:05:11
016 R 10:10:35:24
017 R 10:10:36:00
014 R 10:08:35:04
015 S2 10:09:05:11
016 R 10:10:35:24
017 R 10:10:36:00
Shot data
Serial number (6 digits)
Model name (4 characters)
Model number (4 digits)
Cassette number (4 digits)
6-3
Shot Mark Operations