Sony HKCU-901 User Manual
1-6 (E)
HDCU-900 MM
1-4. Functions of the Indicators on the
Boards
1-4-1. AT-141 Board
AT-141 board (A side and panel side)
D609 : GEN LOCK display
Lights up when external synchronization is established.
Lights up when external synchronization is established.
D611 : /1.001 display
Lights up when the frame frequency factor of the HD
signal is set to 1/1.001 times.
Lights up when the frame frequency factor of the HD
signal is set to 1/1.001 times.
n
Set it with S603 on the AT-141 board. For details, refer to
Section 1-5-1, “AT-141 Board” of “Settings of Switches
and Controls on Boards” of the separate Installation and
Maintenance Manual.
Set it with S603 on the AT-141 board. For details, refer to
Section 1-5-1, “AT-141 Board” of “Settings of Switches
and Controls on Boards” of the separate Installation and
Maintenance Manual.
D612 : REF IN display
Lights up when the reference signal is input to the REFER-
ENCE IN connector on the rear panel of the unit.
Lights up when the reference signal is input to the REFER-
ENCE IN connector on the rear panel of the unit.
D802 : POWER display
Lights up when the voltage used on the board is normally
supplied.
Lights up when the voltage used on the board is normally
supplied.
1-4-2. DPR-163 Board
Board suffix: -11 through -14
DPR-163 board (A side and panel side)
n
When D813 and D821 light in red, be sure to clean the
CAMERA connector of the unit, the CCU connector of the
camera side and optical/electrical cable. It is also recom-
mended to clean them when the indicators light in yellow.
For the cleaning procedure, refer to Section 1-7.
When D813 and D821 light in red, be sure to clean the
CAMERA connector of the unit, the CCU connector of the
camera side and optical/electrical cable. It is also recom-
mended to clean them when the indicators light in yellow.
For the cleaning procedure, refer to Section 1-7.
D801 : /1.001 display
Lights up when the frame frequency factor of the HD
signal is set to 1/1.001 times.
Lights up when the frame frequency factor of the HD
signal is set to 1/1.001 times.
n
Set it with S603 on the AT-141 board. For details, refer to
Section 1-5-1, “AT-141 Board” of “Settings of Switches
and Controls on Boards” of the separate Installation and
Maintenance Manual.
Set it with S603 on the AT-141 board. For details, refer to
Section 1-5-1, “AT-141 Board” of “Settings of Switches
and Controls on Boards” of the separate Installation and
Maintenance Manual.
D802 : 0
Factory use only
Factory use only
A
B
C
D
E
F
G
H
J
K
L
M
1
2
3
4
5
6
7
8
9
AT
POWER
/1.001
FINE
HD BB
REMOTE
LOCAL
LOCAL
REFERENCE H
PHASE
PHASE
MIC LEVEL
REF
IN
GEN
LOCK
NORM
MIN
MIN
1
2
ENG PROD
PRIVATE
NORM
INCOM
SELECT
TALK
LEVEL
PGM
MIX
SIDE
TONE
2 WIRE
CANCEL
CH-1
CH-2
CCU
D609
D612
D611
D802
A
B
C
D
E
F
G
H
J
K
L
M
1
2
3
4
5
6
7
8
9
DPR
POWER
SYSTEM
POWER /1.001
60
50
PSF
CHU LOCK
CCU
CHU
540P
1035
OPTICAL
CONDITION
AUDIO PHASE
30
25
24
MAIN OUTPUT
D803
D801
D904
D907
D814
D810
D807
D805
D817
D819
D821
D813
D802 D804 D806 D808 D811 D812 D815 D818 D820 D822
D901
D902
D903
1-4. Functions of the Indicators on the Boards