Sony HVL-FSL1 User Manual

Page of 2
A
3-076-910-
01
(1)
Slave Flash
HVL-FSL1
Sony Corporation  © 2002  Printed in Japan
取扱説明書
お買い上げいただきありがとうございます。
警告
電気製品は安全のための注意事項を守らないと、火災や人身事故になることがあります。
この取扱説明書には、事故を防ぐための重要な注意事項と製品の取り扱いかたを示してい
ます。この取扱説明書をよくお読みのうえ、製品を安全にお使いください。お読みになっ
たあとは、いつでも見られるところに必ず保管してください。
Operating Instructions
Mode d'emploi
Manual de instrucciones
Bendienungsanleitung
Gebruiksaanwijzing
日本語
安全のために
ソニー製品は安全に
十分配慮して設計さ
れています。しか
し、まちがった使い
かたをすると、感電
などにより人身事故
になることがあり危
険です。事故を防ぐ
ために次のことを必
ずお守りください。
• 安全のための注
意事項を守る
• 故障したら使わ
ずに、テクニカ
ルインフォメー
ションセンター
に修理を依頼す
警告
警告表示の意味
取扱説明書では、次のよ
うな表示をしています。
表示の内容をよく理解し
てから本文をお読みくだ
さい。
警告
この表示の注意事項を守
らないと、火災・感電・
事故などにより死亡や大
けがなど人身事故になる
ことがあります。
注意
この表示の注意事項を守
らないと、感電やその他
の事故によりけがをした
り周辺の家財に損害を与
えたりすることがありま
す。
注意を促す記号
行為を禁止する
記号
下記の注意を守らないと、
感電
により
大けが
原因となります。
分解しない。
内部には電圧の高い部分があ
り、分解したりすると感電の原
因となります。
内部の点検や部品の交換はテク
ニカルインフォメーションセン
ターにご依頼ください。
火の中に入れない。ショートさ
せたり、分解、加熱しない。
乾電池や乾電池パックは充電し
ない。
指定された種類の電池を使用す
る。
+と−の向きを正しく入れる。
電池を使い切ったとき、長期間
使用しないときは、取り出して
おく。
もし電池の液が漏れたときは、電池入れの液をよ
くふきとってから、新しい電池を入れてくださ
い。万一、液が身体や衣服についたときは、水で
よく洗い流してください。
電池についての安全上の
ご注意
漏液、発熱、発火、破裂などを避けるため、
下記のことを必ずお守りください。
警告
注意
スレーブフラッシュの特長
ソニー製デジタルスチルカメラに取り付けて使
用するスレーブフラッシュです。
デジタルスチルカメラに本機を取り付けたまま
で、三脚を使用することができます。
内蔵フラッシュでは光量が不足しているとき、
スレーブフラッシュを使用することにより、被
写体をより鮮明に撮影することができます。
デジタルスチルカメラの内蔵フラッシュの反射
光を感知して発光します。(赤目軽減のプリ発
光では発光しません。本発光のみに同調して発
光します。)
スレーブフラッシュを使用した時の撮影可能距
離は、本体内蔵フラッシュのみ使用した場合の
1.5
2
倍です。
電池の入れかた
本機は、ソニーマンガンリチウム電池
CR123A
1
個を使用します。
1
電池ふたを矢印の方向にずらして開ける。
2
電池を入れる。(この時、極性(プラスとマ
イナス)を間違えないようにご注意くださ
い。)
3
電池ふたを矢印の方向にずらし、カチッとい
うまでしっかりと閉める。
スレーブフラッシュの
取り付けかた
1
スレーブフラッシュに、付属のシューアダプ
ターを取り付ける。
2
シューアダプターのネジをデジタルスチルカ
メラの三脚穴に差し込み、軽く締める。
3
シューアダプターの長さを調節して、スレー
ブフラッシュの位置を決める。
4
シューアダプターのネジをしっかりと締め
る。
使い終わったら
シューアダプターをデジタルスチルカメラに取
り付けた状態で、スレーブフラッシュ本体を着
脱することもできます。スレーブフラッシュ本
体下部の黒いボタンを押しながら(
5
-
1
)、矢
印の方向にスライドさせてください(
5
-
2
)。
持ち運びするときは、スレーブフラッシュを
シューアダプターから取りはずしてください。
使いかた
デジタルスチルカメラの操作に関して詳しく
は、お使いのデジタルスチルカメラの取扱説明
書をご覧ください。
1
デジタルスチルカメラとスレーブフラッシュ
の電源スイッチを「
LOW
HIGH
」のうち、
希望の位置に合わせる。
2
スレーブフラッシュの
READY
ランプが点滅
から点灯に変わったことを確認する。本機は
撮影前に充電をします。充電には約
5
秒(新
品の電池使用時)かかります。充電が完了す
ると、電源ランプがオレンジ色の点滅から点
灯に変わります。
3
デジタルスチルカメラのフラッシュが発光可
能になったことを確認する。詳しくはお使い
のデジタルスチルカメラの取扱説明書をご覧
ください。
4
デジタルスチルカメラを被写体に向けて
フォーカスを合わせ、デジタルスチルカメラ
のシャッターを押す。デジタルスチルカメラ
のフラッシュが発光すると、その光を感知し
本機が発光します。
ご注意
ご使用後は本機の電源スイッチを「
OFF
」にし
てください。
電池が消耗すると、充電時間が長くなります。
スレーブフラッシュが充電されたあとでも、電
源スイッチを「
OFF
」にすると、使用時に再度
充電されます。
ご使用中、受光窓を指で隠さないようご注意く
ださい。
屋外(日中)ではスレーブフラッシュの感度が
低下するため、ご使用いただけません。
強い光源で受光窓をふさいだり、本機を光源に
向けたりする(周囲でフラッシュを使用してい
る時など)と、本機が発光することがありま
す。
背景に反射物がないときは、本機は発光しませ
ん。
新品のソニーマンガンリチウム電池
CR123A
を使用した場合の発光回数は、光量
HIGH
の場
合で約
480
回です。発光回数は使用状況によっ
て変わります。
撮影可能距離について
撮影可能距離は、デジタルスチルカメラの内蔵
フラッシュのガイドナンバー(
GN
)によって変
わります。
詳しくは、お使いのデジタルスチルカメラの取
扱説明書をご覧ください。
例:
DSC-P9
本体内蔵フラッシュ使用時
F
2.8
時 撮影可能距離
3.8
DSC-P9
本体内蔵フラッシュおよびスレー
ブフラッシュ併用時(本機は
HIGH
のとき)
F
2.8
時 撮影可能距離
6.3
READY
ランプについて
オレンジ色の点滅…充電中。
オレンジ色の点灯…充電が完了しました。
本機を使用できます。
赤色の点滅…電池が消耗しています。
新しい電池と交換してください。
赤色のランプが約
2
秒点灯…発光せず。
本機がデジタルスチルカメラ側のフラッシュを
検出しても、被写体が近距離にある場合や、フ
ラッシュの光量が充分あるときには、本機は発
光しません。
緑色の点灯…本機が発光したとき。
お手入れについて
スレーブフラッシュの表面は柔らかい布でから
ぶきしてください。汚れがひどいときは、中性
洗剤溶液を少し含ませた布で拭いてから、もう
一度からぶきしてください。シンナー、ベンジ
ン、アルコールなどは表面の仕上げを傷めます
ので使わないでください。
主な仕様
電源
DC 3 V
 マンガンリチウム電
1
最大発光回数
480
ガイドナンバー
14
相当
最大外形寸法
52.7 
mm
 
×
 60.5 
mm
 
×
37.2 
mm(幅
 
× 
高さ
 
× 
奥行
き)
(最大突起部含まず)
質量 
60g
(電池を含まず)
付属品
シューアダプター(
1
ソニーマンガンリチウム電池
CR123A
1
取扱説明書(
1
保証書(
1
故障かな?と思ったら
修理にお出しになる前に、もう一度点検してく
ださい。
それでも正常に動作しないときは、テクニカル
インフォメーションセンターへご相談くださ
い。
 電源スイッチが入っているのに
READY
ラン
プがつかない。
 →電源スイッチをいったん「
OFF
」にしてから
再度電源を入れてください。電源スイッチ
を入れたまま
15
分が経過すると、電池の消
耗を防ぐために、自動的に電源が切れま
す。
□ 
READY
ランプが赤点滅になったとき
 →電池を交換してください。
  ソニーマンガンリチウム電池
CR123
Aで約
480
回発光できます。 
保証書とアフターサービス
保証書
この製品には保証書が添付されていますので、
お買い上げの際お買い上げ店でお受け取りくだ
さい。
所定事項の記入および記載内容をお確かめのう
え、大切に保存してください。
保証期間は、お買い上げ日より
1
年間です。
アフターサービス
調子が悪いときはまずチェックを
この説明書をもう一度ご覧になってお調べくださ
い。
それでも具合の悪いときは
テクニカルインフォメーションセンターへご相談
ください。
保証期間中の修理は
保証書の記載内容に基づいて修理させていただき
ます。詳しくは保証書をご覧ください。
保証期間経過後の修理は
修理によって機能が維持できる場合は、ご要望に
より有料修理させていただきます。
品名
 : HVL-FSL1
故障の状態
 : 
できるだけ詳しく
購入年月日
感電
分解禁止
警告
感電
分解禁止
この説明書は再生紙を使用しています。
B
1
2
1
2
3
1
2
3
5
ソニー株式会社 〒
141-0001
東京都品川区北品川
6-7-35
電話のおかけ間違いに
ご注意ください。
■テクニカルインフォメーションセンター
ご使用上での不明な点や技術的なご質問のご相
談、および修理受付の窓口です。
製品の品質には万全を期しておりますが、万
一不具合が生じた場合は、「テクニカルイン
フォメーションセンター」までご連絡くださ
い。
修理に関するご案内をさせていただきます。
また修理が必要な場合は、お客様のお宅まで
指定宅配便にて集荷にうかがいますので、ま
ずお電話ください。
電話:
0564-62-4979
受付時間: 月∼金曜日 午前
9
時∼午後
5
(ただし、年末、年始、祝日を除く)
お電話される際に、本機の型名(
HVL-FSL1
をお知らせください。
より迅速な対応が可能になります。
お問い合わせ
窓口のご案内
English
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
This symbol is intended to
alert the user to the
presence of uninsulated
“Dangerous voltage”
within the product’s
enclosure that may be of
sufficient magnitude to
constitute a risk of electric
shock to persons.
This symbol is intended to
alert the user to the
presence of important
operating and
maintenance (servicing)
instructions in the
literature accompanying
the appliance.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
NOTE
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the
following measures:
– Reorient or relocate the receiving
antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced
radio/TV technician for help.
For the customers in Germany
Directive: EMC directive 89/336/EEC, 92/
31/EEC
This equipment complies with EMC
regulations when used under the
following circumstances:
– Residential area
– Business district
– Light-industry district
(This equipment complies with the EMC
standard regulations EN55022 ClassB.)
CAUTION
Danger of explosion if battery is
incorrectly replaced.
Replace only with the same or equivalent
type recommended by the manufacturer.
Discard used batteries according to the
manufacturer's instructions.
Replace the battery with a Sony CR123A
lithium manganese dioxide battery. Use of
another battery may present a risk of fire
or explosion.
WARNING
Battery may explode if mistreated. Do not
recharge, disassemble or dispose of in fire.
Slave Flash Features
• The slave flash is for use with the Sony
digital still camera.
• You can also use the tripod while fitting
the Slave Flash with the shoe adapter.
• The slave flash lets you take clear photos
even when there is insufficient light from
the built-in flash of the digital still
camera.
• The slave flash senses the reflected light
from the built-in flash and fires of the
digital still camera. (It does not fire with
the pre-flash for red-eye prevention. It
only fires in synchronization with the
main flash.)
• The distance at which photos can be
taken with the slave flash is about one
and half or two times that with only the
built-in flash.
Inserting the
Battery
The slave flash uses one Sony CR123A
lithium manganese dioxide battery.
1 Slide open the battery cover in the
direction of the arrow.
2 Insert the battery, making sure the
polarity of the battery is correct.
3 Slide the battery cover closed in
the direction of the arrow until it
clicks into place.
Fitting the Slave
Flash
1 Fit the slave flash with the shoe
adapter provided.
2 Insert the screw of the shoe
adapter into the tripod hole of the
digital still camera and lightly
tighten it.
3 Adjust the length of the shoe
adapter and choose the position of
the slave flash.
4 Firmly tighten the screw of the
shoe adapter.
After Use
• You can remove and attach the slave
flash with the shoe adapter still fitted to
the digital still camera. Slide the slave
flash in the direction of the arrow (5-2)
while pressing the black button at the
bottom (5-1).
• Remove the slave flash from the shoe
adapter when carrying.
Using the Slave
Flash
For details of how to use the digital still
camera, please refer to the digital still
camera instruction manual.
1 Set the power switches of the
digital still camera and the slave
flash to LOW or HIGH, as required.
2 Check that the slave flash’s READY
lamp has stopped flashing and is
glowing. The slave flash must be
charged before taking a photo.
Charging takes about 5 seconds, (if
the battery is new). When
charging is complete, the orange
power lamp stops flashing and
glows.
3 Check that the built-in flash of the
digital still camera is ready to fire.
For details, please refer to the
digital still camera instruction
manual.
4 Point the digital still camera and
focus before pressing the shutter
button. When the built-in flash
fires of the digital still camera, the
slave flash senses the light and
also fires.
Note
• Switch off the slave flash after use.
• The battery takes longer to charge as it
gets older.
• Even if the slave flash is charged when
you turn it off, you must charge it again
before it can fire.
• Be careful not to block the light receptor
with your finger during use.
• The slave flash cannot be used outdoors
or in sunlight because its sensitivity is
reduced.
• The slave flash may fire if facing a light
source or if the light receptor is filled
with a powerful light source (such as
using a flash around you).
• The slave flash does not fire when there
is no reflective object in the background.
• The slave flash can fire approximately
480 times with a new Sony CR123A
lithium manganese dioxide battery and
the light amount set to HIGH. This
number varies according to the
conditions of use.
Recommended
Distance
The recommended distance varies with the
guide number (GN) of the build-in flash of
the digital still camera.
For details, please refer to the digital still
camera instruction manual.
Example:
When using a DSC-P9 built-in flash
At f-stop 2.8, the recommended
distance is 3.8m.
When using a DSC-P9 built-in flash and
slave flash together (when this unit is
set to HIGH)
At f-stop 2.8, the recommended
distance is 6.3m.
READY Lamp
• Flashes orange... Charging is underway.
• Glows orange... Charging is complete.
The slave flash can now be used.
• Flashes red... The battery is wearing out.
Replace it with a new one.
• Glows red for about 2 seconds then goes
off... The slave flash will not fire even if it
detects the built-in flash of the digital still
camera, the object is within range, and
the quantity of flash light is sufficient.
• Glows green... The slave flash has fired.
Maintenance
Wipe the surface of the slave flash with a
soft cloth. If it is very dirty, dampen the
cloth slightly with a neutral cleanser and
wipe again. Do not use thinners, benzene
or alcohol, which damage the surface of
the slave flash.
Main Specifications
Power Source 3V DC lithium manganese
dioxide battery
Guide number Around 14
Max. No. of Flashes
Approx. 480
Max. Dimensions
52.7mm 
×
 60.5mm 
×
37.2mm (w 
×
 h 
×
 d)
(excluding protruding
parts)
Weight
Approx. 60g (not including
batteries)
Accessories
Shoe adaptor (1)
Sony CR123A lithium manganese
dioxide battery (1)
Instruction manual (1)
Troubleshooting
s
If the READY lamp does not light up
when the power switch is turned on
t Turn the power switch “OFF” and
then on again.
When the flash is left untouched with
the power turned on, it automatically
turns itself off after 15 minutes in
order to prevent battery wear.
s
If the READY lamp flashes red
t Replace the battery.
      Sony CR123A lithium manganese
dioxide battery lasts for about 480
flashes.
AVERTISSEMENT
Afin d’éviter tout risque d’incendie ou
d’électrocution, ne pas exposer cet
appareil à la pluie ou à l’humidité.
ATTENTION
Il existe un risque d’explosion si la pile est
remplacée de façon incorrecte.
Remplacez-la uniquement par une de type
identique ou équivalent, recommandé par
le fabricant.
Éliminez les piles usagées conformément
aux instructions de leur fabricant.
Remplacez la pile par une pile Sony
CR123A au lithium et dioxyde de
manganèse. L’emploi d’une autre pile peut
présenter un risque d’incendie ou
d’explosion.
AVERTISSEMENT
La pile peut exploser si elle est traitée de
façon inappropriée. Ne la rechargez pas,
ne la démontez pas et ne la jetez pas dans
un feu.
Caractéristiques du
flash asservi
• Le flash asservi est conçu pour servir
avec l’appareil photo numérique Sony.
•Vous pouvez également utiliser le trépied
en installant le flash asservi sur
l’adaptateur porte-accessoire.
• Le flash asservi vous permet de prendre
des photos nettes, même si le flash
incorporé à l’appareil photo numérique
ne fournit pas une lumière suffisante.
• Le flash asservi capte la lumière
réfléchie, provenant du flash incorporé,
et il se déclenche sur l’appareil photo
numérique. (Il ne se déclenche pas avec
un pré-flash pour réduire l’effet des yeux
rouges. Il se déclenche simplement en
synchronisation avec le flash principal.)
• La distance à laquelle des photos
peuvent être prises avec le flash asservi
est entre 1,5 et 2 fois celle disponible avec
le flash incorporé seul.
Mise en place de
la pile
Le flash asservi s’alimente sur une pile
Sony CR123A (lithium et dioxyde de
manganèse).
1 Ouvrez le couvercle de la pile en le
glissant dans le sens de la flèche.
2 Installez la pile en respectant ses
polarités.
3 Refermez le couvercle de la pile en
le glissant dans le sens de la flèche
jusqu’à son encliquetage.
B Installation du
Flash asservi
1 Installez le flash asservi sur
l’adaptateur de porte-accessoire
fourni.
2 Insérez la vis de l’adaptateur de
porte-accessoire dans l’orifice de
trépied sur l’appareil photo
numérique et serrez-la légèrement.
3 Ajustez la longueur de
l’adaptateur de porte-accessoire et
déterminez la position du flash
asservi.
4 Serrez fermement la vis de
l’adaptateur de porte-accessoire.
Après l’utilisation
• Vous pouvez déposer et fixer le flash
asservi en laissant l’adaptateur de porte-
accessoire installé sur l’appareil photo
numérique. Glissez le flash asservi dans
le sens de la flèche (5-2) en appuyant
sur le bouton noir dans le bas (5-1).
• Retirez le flash asservi de l’adaptateur de
porte-accessoire lorsque vous le
transportez.
Utilisation du flash
asservi
Pour les détails sur l’utilisation de
l’appareil photo numérique, reportez-vous
à son mode d’emploi.
1 Réglez les interrupteurs
d’alimentation de l’appareil photo
numérique et du flash asservi sur
LOW ou HIGH, selon les besoins.
2 Assurez-vous que le voyant READY
du flash asservi a cessé de
clignoter et qu’il reste allumé. Le
flash asservi doit être rechargé
avant de prendre une photo. Une
recharge prend 5 secondes environ
(si la pile est neuve). À la fin de la
recharge, le voyant d’alimentation
orange cesse de clignoter et il
reste allumé.
3 Assurez-vous que le flash
incorporé à l’appareil photo
numérique est prêt à fonctionner.
À ce sujet, reportez-vous au mode
d’emploi de l’appareil photo
numérique.
4 Dirigez l’appareil photo numérique
vers le sujet et effectuez la mise au
point avant d’appuyer sur le
déclencheur. Lorsque le flash
incorporé à l’appareil photo
numérique se déclenche, le flash
asservi détecte l’éclair et il se
déclenche aussi.
Remarques
• Désactivez le flash asservi après son
utilisation.
• Plus la pile vieillit, plus longtemps dure
la recharge.
• Même si le flash asservi est chargé
lorsqu’il est désactivé, il doit être chargé
à nouveau avant de pouvoir se
déclencher.
• Prenez soin de ne pas faire obstacle au
capteur de lumière avec les doigts
pendant l’utilisation du flash.
• Le flash asservi ne peut pas fonctionner à
l’extérieur ou au soleil parce que sa
sensibilité est réduite.
• Le flash asservi peut se déclencher s’il
fait face à une source de lumière ou si le
capteur de lumière reçoit une forte
lumière (par exemple, si vous utilisez un
flash près de vous).
• Le flash asservi ne se déclenche pas s’il
n’y a pas d’objet réfléchissant à l’arrière-
plan.
• Le flash asservi peut fonctionner 480 fois
avec une nouvelle pile Sony CR 123A au
lithium et dioxyde de manganèse et si le
réglage de lumière est sur HIGH. Ce
nombre varie en fonction des conditions
d’utilisation.
Distance Éclair -
Sujet
La distance recommandedée l’éclair au
sujet varie selon le nombre-guide (NG) du
flash incorporé à l’appareil photo
numérique. Pour les détails, reportez-vous
au mode d’emploi de l’appareil photo
numérique.
Exemple:
Si vous utilisez un flash incorporé DSC-
P9(quand cette unité est réglée sur
HIGH):
À l’ouverture 2.8, la distance éclair-
sujet est de 3,8 m.
Si vous utilisez ensemble un flash
incorporé DSC-P9 et le flash asservi:
À l’ouverture 2.8, la distance éclair-
sujet est de 6,3 m.
Voyant READY
• Il clignote en orange ... La recharge est en
cours.
• Il s’allume en orange ... La recharge est
terminée. Le flash asservi peut
fonctionner.
• Il clignote en rouge ... La pile est usée.
Remplacez-la par une  neuve.
• Il s’allume en rouge pendant 2 secondes
puis s’éteint ... Le flash asservi ne se
déclenchera pas même s’il détecte l’éclair
du flash incorporé de l’appareil photo
numérique, l’objet est dans la plage
voulue et la quantité de lumière du flash
est suffisante.
• Il s’allume en vert ... Le flash asservi s’est
déclenché.
Entretien
Nettoyez la surface du flash asservi avec
un linge doux. Si elle est très sale,
humectez le linge avec un produit de
nettoyage neutre et utilisez-le pour le
nettoyage. N’utilisez pas de diluant pour
peinture, benzène ou alcool car ces
produits endommageraient la surface du
flash asservi.
Spécifications
principales
Source d’alimentation Pile de 3 V, lithium
et dioxyde de manganèse
Nombre-guide Autour de 14
Nombre maximum d’éclairs
Env. 480
Dimensions maximum 52,7 x 60,5 x 37,2
mm (L x H x P) (sans les
parties saillantes)
Poids
Env. 60 g (pile non
comprise)
Accessoires
Adaptateur de porte-accessoire (1)
Pile Sony CR123A, lithium et dioxyde
de manganèse (1)
Mode d’emploi (1)
Guide de dépannage
s
Si le voyant READY ne s’allume pas
lorsque l’interrupteur d’alimentation est
allumé
t Tournez l’interrupteur
d’alimentation sur “OFF”, puis à
nouveau sur on.
Si le flash n’est pas utilisé pendant 15
minutes après avoir été activé, il se
met automatiquement hors service
pour éviter une décharge de la pile.
s
Si le voyant READY clignote en rouge
t Remplacez la pile.
Une pile Sony CR123A au lithium et
dioxyde de manganèse peut fournir
environ 480 éclairs.
Français