Sony ICFCD3iPSIL User Manual

The model number and the serial number are located on the 

bottom. 

Record the serial number in the space provided below. Refer 

to them whenever you call upon your Sony dealer regarding 

this product.
Model No. ICF-CD3iP

 

Serial No. ________________________________

For customers who purchased this product in the 

USA

Please register this product on line at 

http://www.sony.com/productregistration.

Proper registration will enable us to send you 

periodic updates about new products, services, and 

other important announcements. Registering your 

product will also allow us to contact you in the 

unlikely event that the product needs adjustment 

or modification. Thank you.

To reduce the risk of fire, do not cover the 

ventilation opening of the apparatus with 

newspapers, tablecloths, curtains, etc. Do not 

place the naked flame sources such as lighted 

candles on the apparatus.

To reduce the risk of fire or electric shock, do not 

expose this apparatus to dripping or splashing, 

and do not place objects filled with liquids, such 

as vases, on the apparatus.
Do not install the appliance in a confined space, 

such as a bookcase or built-in cabinet.
Do not expose the batteries (battery pack or 

batteries installed) to excessive heat such as 

sunshine, fire or the like for a long time.
As the main plug is used to disconnect the unit 

from the mains, connect the unit to an easily 

accessible AC outlet. Should you notice an 

abnormality in the unit, disconnect the main plug 

from the AC outlet immediately.
You are cautioned that any changes or  

modifications not expressly approved in this 

manual could void your authority to operate this 

equipment.

CAUTION
 The use of optical instruments with this 

product will increase eye hazard.

 Danger of explosion if battery is incorrectly 

replaced. Replace only with the same or 

equivalent type.

This symbol is intended to alert the user 

to the presence of uninsulated “dangerous 

voltage” within the product’s enclosure that 

may be of sufficient magnitude to constitute 

a risk of electric shock to persons.
This symbol is intended to alert the user to 

the presence of important operating and 

maintenance (servicing) instructions in the 

literature accompanying the appliance.

CLASS1M INVISIBLE LASER RADIATION 

WHEN OPEN DO NOT VIEW DIRECTRY 

WITH OPTICAL INSTRUMENTS.

Use of controls or adjustments or performance of 

procedures other than those specified herein may 

result in hazardous radiation exposure.

This equipment has been tested and found to 

comply with the limits for a Class B digital device, 

pursuant to Part 15 of the FCC Rules. These limits 

are designed to provide reasonable protection 

against harmful interference in a residential 

installation. This equipment generates, uses and 

can radiate radio frequency energy and, if not 

installed and used in accordance with the 

instructions, may cause harmful interference to 

radio communications. However, there is no 

guarantee that interference will not occur in a 

particular installation. If this equipment does 

cause harmful interference to radio or television 

reception, which can be determined by turning 

the equipment off and on, the user is encouraged 

to try to correct the interference by one or more 

of the following measures:

— Reorient or relocate the receiving  

 

antenna.

— Increase the separation between the equipment 

and receiver.

— Connect the equipment into an outlet on a circuit 

different from that to which the receiver is  

connected.

— Consult the dealer or an experienced radio/TV 

technician for help.

WARNING
 Replace the battery for the clock backup with a 

Sony CR2032 lithium battery, and the battery 

for the remote commander with a Sony CR2025 

lithium battery. Use of another battery may 

present a risk of fire or explosion. 

 Battery may explode if mistreated. Do not 

recharge, disassemble or dispose of in fire.

 Do not expose the battery to excessive heat 

such as direct sunlight, fire or the like.

 Dispose of used battery promptly. Keep away 

from children.

1)  Read these instructions.

2)  Keep these instructions.

3)  Heed all warnings.

4)  Follow all instructions.

5)  Do not use this apparatus near water.

6)  Clean only with dry cloth.

7)  Do not block any ventilation openings. 

Install in accordance with the manufacturer’s 

instructions.

8)  Do not install near any heat sources such as 

radiators, heat registers, stoves, or other 

apparatus (including amplifiers) that produce 

heat.

9)  Do not defeat the safety purpose of the 

polarized or grounding-type plug. A polarized 

plug has two blades with one wider than the 

other. A grounding type plug has two blades 

and a third grounding prong. The wide blade 

or the third prong are provided for your safety. 

If the provided plug does not fit into your 

outlet, consult an electrician for replacement 

of the obsolete outlet.

10) Protect the power cord from being walked on 

or pinched particularly at plugs, convenience 

receptacles, and the point where they exit 

from the apparatus.

11) Only use attachments/accessories specified by 

the manufacturer.

12) Use only with the cart, stand, tripod, bracket, 

or table specified by the manufacturer, or sold 

with the apparatus. When a cart is used, use 

caution when moving the cart/apparatus 

combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms 

or when unused for long periods of time.

14) Refer all servicing to qualified service 

personnel. Servicing is required when the 

apparatus has been damaged in any way, such 

as power-supply cord or plug is damaged, 

liquid has been spilled or objects have fallen 

into the apparatus, the apparatus has been 

exposed to rain or moisture, does not operate 

normally, or has been dropped.

Perchlorate Material –special handling may apply, See 

www.dtsc.ca.gov/hazardouswaste/perchlorate

Perchlorate Material: Lithium battery contains 

perchlorate

 Brightness control (High/Mid/Low)

 Supplied audio cable for digital music players

 Built-in CD player with CD-R/RW playback 

function

 FM/AM 2-band digital tuner

 30 Station Presets (20 FM, 10 AM)

 Automatic Time/Daylight Saving Time Setting

 No Power No Problem alarm system to keep 

the clock and the alarm operating during a 

power interruption with a CR2032 battery 

installed

 Extendable Snooze time from 10 to 60 min

 Play the unit on the power source specified in 

“Specifications”.

 To disconnect the AC power cord (mains lead), 

pull it out by the plug, not the cord.

 The unit is not disconnected from the AC 

power source (mains) as long as it is connected 

to the wall outlet, even if the player itself has 

been turned off.

 The nameplate and important information 

concerning safety are located on the bottom 

exterior.

 Since a strong magnet is used for the speaker, 

keep personal credit cards using magnetic coding 

or spring-wound watches away from the unit to 

prevent possible damage from the magnet.

 Do not leave the unit in a location near a heat 

source such as a radiator or airduct, or in a 

place subject to direct sunlight, excessive dust, 

mechanical vibration, or shock.

 Allow adequate air circulation to prevent 

internal heat build-up. Do not place the unit on 

a surface (a rug, a blanket, etc.) or near 

materials (a curtain) which might block the 

ventilation holes.

 Should any solid object or liquid fall into the unit, 

unplug the unit and have it checked by qualified 

personnel before operating it any further.

 To clean the casing, use a soft cloth dampened 

with a mild detergent solution.

 Never touch the wire of the external FM 

antenna during a thunderstorm. Furthermore, 

immediately disconnect the AC power cord 

from the radio.

NOTES ON LITHIUM BATTERY
 Wipe the battery with a dry cloth to assure a 

good contact.

 Be sure to observe the correct polarity when 

installing the battery.

 Do not hold the battery with metallic tweezers, 

otherwise a short-circuit may occur.

If you have any questions or problems concerning 

your unit, please consult your nearest Sony dealer.

Should any problem persist after you have made 

the following checks, consult your nearest Sony 

dealer.
The clock flashes “AM 12:00” due to a power 

interruption.
 The battery is low. Replace the battery. Remove 

the old battery and install a new one.

sound at the preset alarm time.
 Check that “ALARM A” or “ALARM B” is 

properly displayed. 

time.
 Has VOLUME been adjusted?
The CD player does not operate.
 Did you close the CD compartment lid?

 Did you insert the disc correctly?  

The disc should be inserted with the label side 

up.

 Dusty or defective disc — Clean the disc with 

an optional cleaning cloth. Wipe the disc from 

the center out.

 Take out the CD and leave the CD 

compartment open for about an hour to allow 

condensation to evaporate.

There is no sound from the iPod.
 Make sure the iPod is securely connected.

 Adjust the VOLUME.
The iPod cannot be operated with this unit.
 Make sure the iPod is securely connected.
The iPod cannot be charged.
 Make sure the iPod is securely connected.
When daylight saving time begins, the clock 

automatically.
 Make sure the clock is set correctly.

 Press and hold CLOCK and BRIGHTNESS/ 

TIME ZONE simultaneously for at least two 

seconds to employ the DST function.

POWER OUTPUT AND TOTAL HARMONIC 

DISTORTION

With 20-ohm loads, both channels driven from 

150-10,000 kHz; rated 0.7W per channel-

minimum RMS, with no more than 10% total 

harmonic distortion.
CD player section
System

Compact disc digital audio system
Laser diode properties

Emission duration: Continuous

Laser output: Less than 44.6 µW(This output is 

the value measurement at a distance of 200 mm 

from the objective lens surface on the optical 

pick-up block with 7 mm aperture.)
Number of channels

2
Frequency response

20 - 20 000 Hz +1/–2 dB

Below measurable limit

4-270-865-12(1)

©2008 Sony Corporation          Printed in China

ICF-CD3iP

FM/AM CD

Clock Radio

Operating Instructions

Dream Machine is a trademark of Sony Corporation.

This unit includes a preinstalled Sony Lithium battery (CR2032) as back-up power source for the clock, which is preset 

to EST (Eastern Standard Time) at the factory. And this battery is considered part of the product.

The shape and the length of the antenna is 

designed to receive AM signals. Do not dismantle 

or roll up the antenna.

  Remove only the loop part from the 

plastic stand.

  Set up the AM loop antenna.

  Connect the cords to the AM antenna 

terminals.

Cord (A) or cord (B) can be connected to 

either terminal.

  Make sure the AM loop antenna is 

connected firmly by pulling softly.

Find a place and an orientation that provide good 

reception.

 Do not place the AM loop antenna near the 

unit or other AV equipment, as noise may 

result.

Adjust the direction of the AM loop antenna for 

best AM broadcast sound.

To keep good time, this unit contains one CR2032 

battery inside of the unit as a backup power 

source.

The battery keeps the clock operating in the event 

of a power interruption.

When the battery becomes weak, “” appears in 

the display.

If a power interruption occurs while the battery is 

weak, the current time and alarm will be erased.

Replace the battery with a Sony CR2032 lithium 

battery. Use of another battery may cause a fire or 

explosion.
Note

If “AM 12:00” flashes in the display when the unit 

is connected to AC outlet for the first time, the 

battery may be weak. In this case, consult your 

Sony dealer.

  Open the CD compartment lid. (See Fig. 

-)

  Keep the AC plug connected to the AC 

outlet and use a screwdriver to remove 

the screw that secures the battery holder 

at the bottom of the unit. (See Fig. -

)

  Push the exhausted battery out from the 

bottom of the battery holder and insert a 

new battery with the  side facing up. 

(See Fig. -)

  Insert the battery holder back into the 

unit and secure it with the screw. (See 

Fig. -)

  Press CD, iPod&iPhone, RADIO BAND, 

AUDIO IN or SNOOZE/DATE/SLEEP 

OFF to turn “



” off in the display.

DC out: 5V

MAX: 500mA (AC only)
Radio section
Frequency range

FM

87.5 – 108 MHz 0.1 MHz

AM

530 – 1 710 kHz 10 kHz

Approx. 3.8 cm (1 

1

/

2

 inches) dia. 20 Ω

AUDIO IN jack (ø 3.5 mm stereo minijack)
Power output

1 W + 1 W (at 10% harmonic distortion)
Power requirements

120 V AC, 60 Hz

For clock back up: 3V DC, one CR2032 battery
Dimensions

Approx. 145 × 156.8 × 115.8 mm (w/h/d)  

(5 

3

/

4

 × 6 

1

/

4

 × 4 

5

/

8

 inches) not including 

projecting parts and controls
Mass

Approx. 1.3 kg (2 lb 13 oz) including power 

supply unit
Supplied accessories

Remote commander (1)

AM loop antenna (1)

Audio connecting cable (1)

Universal Dock Adapter for iPhone (1)

Universal Dock Adapter for iPhone 3GS &  

iPhone 3G (1)

Universal Dock Adapter for iPhone 4S & iPhone 4 

(1)
Design and specifications are subject to change 

without notice.

Compatible iPod/iPhone models are as follows. 

Update your iPod/iPhone to use the latest 

software before you use it.

iPod touch (4th generation)

iPod touch (3rd generation)

iPod touch (2nd generation)

iPod touch (1st generation)

iPod nano (6th generation)*

iPod nano (5th generation)

iPod nano (4th generation)

iPod nano (3rd generation)

iPod nano (2nd generation)

iPod nano (1st generation)

iPod with video

iPod with color display

iPod with click wheel

iPod classic

iPod mini

iPhone 4S

iPhone 4

iPhone 3GS

iPhone 3G

iPhone
*  The iPod nano (6th generation) cannot be 

controlled by the remote when the command of 

“MENU,” “,” “,” and “ENTER” is pressed.

Notes
 In these Operating Instructions, “iPod” is used 

as a general reference to functions of iPod on 

the iPod and iPhone, unless otherwise specified 

by the text or illustrations.

 The connector of the unit is for sole use for 

iPod. When you use devices that do not match 

with the connector, connect to the AUDIO IN 

terminal of this unit with the supplied audio 

connecting cable.

 Sony cannot accept responsibility in the event 

that data recorded to iPod is lost or damaged 

when using an iPod connected to this unit.



The CD, iPod & iPhone  and 







No Power No Problem is a trademark of Sony Corporation.











Before using the card remote commander for the 

first time, remove the insulation film. (See Fig. 

-)

With normal use, the battery (CR2025) should 

last for about six months. When the remote 

commander no longer operates the unit, replace 

the battery with a new one. (See Fig. -)

Notes
 Do not charge the battery.

 When you are not going to use the remote 

commander for a long time, remove the battery 

to avoid any damage caused by leakage and 

corrosion.

Press the Reset button with a pointed device. The 

Reset button is in the small hole located in the 

battery compartment. 
Note

When you replace the battery, do not disconnect 

the plug from the AC outlet. Otherwise, the 

calendar, current time, alarm and station presets 

will be erased.
Battery Warning

If the unit is to be left unplugged for a long time, 

remove the battery to avoid undue battery 

discharge and damage to the unit from battery 

leakage.
WARNING

There is a danger of explosion if the battery is 

incorrectly replaced.

Replace only with the same or equivalent type 

recommended by the equipment manufacturer.
If the battery compartment lid comes off

The battery compartment lid is designed to come 

off when opened with excessive force. To put it 

back on, see the illustration. 

  Insert the left hook of the lid into the left 

hole in the unit.

  Insert the right hook into the right hole.

  Confirm the lid is securely attached.