Sony KDP 51WS655 User Manual

The projection tube image appears on the screen in three colors (red, 
green and blue). If the three colors do not project properly, the color is 
poor and the picture blurs. Before you use your TV, be sure to run the 
Flash Focus feature. Flash Focus adjusts the color projection settings 
automatically.

Tune to a TV or cable TV program.

Press the 

FLASH FOCUS

 button on the front panel of the TV.

The cross pattern appears and Flash Focus begins to work.

The adjustment is completed when the TV picture returns.

❑

Use the manual Convergence feature, as described in the 
Operating Instructions.

❑

You cannot perform any other functions until Flash Focus has 
completed its cycle. If you perform any other operation while 
Flash Focus is in progress, the Flash Focus operation is canceled.

Allow the TV to warm up for about 30 minutes before you adjust the 
convergence with Flash Focus.

,

Review the following chart to determine which diagram to use to 
connect the components in your system:

❑

See the “Cables Required” chart that appears with the diagram to 
determine which cables you’ll need. You may need to purchase 
extra accessories, such as cables and splitters, depending on the 
components you plan to connect.

❑

Turn off and unplug all components before making connections.

❑

If you have a component such as a DVD player that includes a 
DVI video output, you can connect it to the TV’s HDMI input 
using a DVI-to-HDMI cable (and analog audio cables).

❑

If you are connecting a digital cable box, you’ll need a special bi-
directional splitter that’s compatible with your cable box. Contact 
your cable provider for details.

Your TV includes several types of video inputs. Use the inputs that 
are available on your components that provide the best video 
performance, as described below. 

For best audio performance, connect your digital audio components 
using either digital optical or digital coaxial audio connections.

Depending on which components are in your system, you may need 
to complete additional connections. For example, if you have a 
satellite receiver, you’ll need to connect the satellite antenna. If you 
have an A/V receiver, you’ll need to connect speakers. 

A

B

C

D

E

F

HDMI (High-Definition Multimedia Interface)

Component video 

S VIDEO

Composite video

RF/Coaxial

If you are using a CableCARD or the digital audio (optical) output connector, 
see the Operating Instructions for details.

The connection diagrams shown on the reverse side are recommendations 
only; other possible solutions may exist. Connections that include an A/V 
receiver can often be very complex, so check your A/V receiver’s instruction 
manual for additional details.

 

  

Player

 

  

Player

 

 

 

 

  

Player

 

 

  

Player

 

 

 

 

 

  

Player

 

 

 

 

 

After you finish connecting the TV, you need to run Initial Setup, 
which automatically creates a list of available analog and digital 
channels. The Initial Setup screens appear when you turn on your TV 
for the first time after hooking it up. 

Press 

POWER

 to turn on the TV. 

The Initial Setup screen appears.

Using the remote control, move the highlight to the desired 
language, then press to select that language. 
The next screen instructs you to connect your cable/antenna. 
Check that you’ve connected your signal source correctly.

To start Auto Program, highlight 

Yes

 and then press 

.

Auto Program automatically creates a list of receivable analog and 
digital channels. Auto Program may take 50 minutes or more to 
complete. A progress bar is displayed while the channel list is 
being created.

The lowest numbered channel is displayed.

Along with your new projection TV, the package contains a remote 
control and two AA batteries. No additional cables are included. 
These items are all you need to set up and operate the projection TV 
in its basic configuration. 

Remove the battery cover from the remote control.

Insert two size AA (R6) batteries (supplied) by matching the e 
and E terminals on the batteries to the diagram inside the battery 
compartment.

Replace the battery cover.

❑

Remove the batteries to avoid damage from possible battery 
leakage whenever you anticipate that the remote control will not 
be used for an extended period. 

❑

Handle the remote control with care. 

❑

Avoid dropping it, getting it wet, placing it in direct sunlight, near 
a heater, or where the humidity is high.

❑

Be careful when moving the TV.

❑

When you place the TV in position, be careful not to drop it on 
your foot or fingers.

❑

Watch your footing while installing the TV.

❑

If you carry the TV in a manner other than the specified manner 
and without the specified number of persons, it may drop and a 
serious injury may be caused. Be sure to follow the instructions 
mentioned below.

❑

Carrying the TV requires four or more people. 

❑

Do not carry the TV holding the speaker grill.

❑

Hold the TV tightly when carrying it.

❑

The TV includes casters. Be sure to move your projection TV 
using these casters. 

2-148-833-01(1)

©

 2004 Sony Corporation 

http://www.sony.net 

Printed in U.S.A.

If, after reading the Operating Instructions and this Quick 
Setup Guide, you have additional questions related to the 
use of your Sony television, please call our Customer 
Information Services Center at:
1-800-222-SONY (7669) (US residents only) or 
(416) 499-SONY (7669) (Canadian residents only). 

Connecting Your 
Projection TV
(see reverse side)

QSG.fm  Page 1  Thursday, August 12, 2004  3:00 PM