Sony KL-X9200J User Manual
Additional Information
GB
29
-GB
Troubleshooting
If the problem persists after trying the methods below,
contact your nearest Sony dealer.
contact your nearest Sony dealer.
No picture
/
Check that the power cord is connected
firmly.
firmly.
/
Is the power of the monitor turned on?
/
Is the air filter mounted securely? (page 27)
/
Is the lamp cover attached securely? (page
28)
28)
/
Check that the power of the connected
equipment is turned on.
equipment is turned on.
/
Try to press any key on the connected
computer’s keyboard.
computer’s keyboard.
/
Check that the RGB signal cable or audio/
video cords are properly connected. (The
supplied HD15-HD15 adaptor may be
needed for some models of IBM PC/AT or
compatible computers. For a Macintosh or
compatible computer, use the supplied
Macintosh adaptor.) (pages 7 and 8)
video cords are properly connected. (The
supplied HD15-HD15 adaptor may be
needed for some models of IBM PC/AT or
compatible computers. For a Macintosh or
compatible computer, use the supplied
Macintosh adaptor.) (pages 7 and 8)
/
Make sure that no pins on the HD15
connectors are bent.
connectors are bent.
/
Check that the connected computer’s video
card is seated completely in the proper bus
slot.
card is seated completely in the proper bus
slot.
/
Check that the frequency range of the input
signal is within that specified for the
monitor. (If not, “OUT OF SCAN RANGE”
appears on the screen.) (page 9)
signal is within that specified for the
monitor. (If not, “OUT OF SCAN RANGE”
appears on the screen.) (page 9)
/
The monitor does not accept an interlace
mode signal that is not a preset mode
signal.
mode signal that is not a preset mode
signal.
/
For customers using Windows 95/98 — If
“KL-X9200” is not displayed as “Monitor
type” in the device selection screen in
Windows 95/98, select “Plug and Play
monitor (VESA DDC)” as “Monitor type.”
“KL-X9200” is not displayed as “Monitor
type” in the device selection screen in
Windows 95/98, select “Plug and Play
monitor (VESA DDC)” as “Monitor type.”
Picture and sound output are delayed
/
When the green u (power) indicator on the
front is flashing, the monitor is warming
up.
front is flashing, the monitor is warming
up.
/
To protect the lamp, the monitor does not
immediately output the picture and sound
if you try to turn on the power more than 5
seconds after the power has been turned
off.
immediately output the picture and sound
if you try to turn on the power more than 5
seconds after the power has been turned
off.
Good picture, no sound
/
Press VOL+ (VOLUME+).
/
Press MUTING so that “MUTING”
disappears from the screen. (page 16)
disappears from the screen. (page 16)
/
The volume of the computer may be low.
/
Check that the audio connecting cord is
connected firmly to the audio outputs on
the computer.
connected firmly to the audio outputs on
the computer.
Fuzzy picture
/
If you use the monitor in a cold place,
moisture condensation may have occurred.
Leave the monitor as it is to let the
moisture evaporate.
moisture condensation may have occurred.
Leave the monitor as it is to let the
moisture evaporate.
Dark picture
/
Replace the lamp for the light source with a
new one. (page 28)
new one. (page 28)
No color, abnormal color
/
Adjust the picture in the VIDEO ADJUST
menu. (pages 20 and 21)
menu. (pages 20 and 21)
/
Select an appropriate color system from the
COLOR SYSTEM option in the OPTION
menu to obtain optimum color.
COLOR SYSTEM option in the OPTION
menu to obtain optimum color.
Computer picture not clear
/
Adjust PITCH, then PHASE in the DOT
ADJUST menu. (page 18)
ADJUST menu. (page 18)
Horizontal lines of the computer picture are
not visible.
not visible.
/
Check that TIMING in the DOT ADJUST
menu is set to YES. (page 18)
menu is set to YES. (page 18)
Computer picture not centered or sized
properly
properly
/
Adjust the centering and size so that the
picture fits the screen. (pages 16 and 17)
picture fits the screen. (pages 16 and 17)
(continued)