Sony LBT-LV100AV User Manual
59
Specifications
Amplifier section
Front Speaker:
The following measured at AC 220 V, 50Hz
DIN power output (Rated)
The following measured at AC 220 V, 50Hz
DIN power output (Rated)
150 + 150 watts
(6 ohms at 1 kHz, DIN)
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (Reference)
200 + 200 watts
(6 ohms at 1 kHz, 10%
THD)
(6 ohms at 1 kHz, 10%
THD)
Center Speaker:
DIN power output (Rated)
DIN power output (Rated)
35 watts
(8 ohms at 1 kHz, DIN)
(8 ohms at 1 kHz, DIN)
Continuous RMS power output (Reference)
50 watts
(8 ohms at 1 kHz, 10%
THD)
(8 ohms at 1 kHz, 10%
THD)
Rear Speaker:
DIN power output (Rated)
DIN power output (Rated)
35 + 35 watts
(8 ohms at 1 kHz, DIN)
(8 ohms at 1 kHz, DIN)
Continuous RMS power output (Reference)
50 + 50 watts
(8 ohms at 1 kHz, 10%
THD)
(8 ohms at 1 kHz, 10%
THD)
Inputs
PHONO IN (phono jacks):sensitivity 3 mV,
PHONO IN (phono jacks):sensitivity 3 mV,
impedance 47 kilohms
MIC 1/2 (phone jack):
sensitivity 1 mV,
impedance 10 kilohms
impedance 10 kilohms
VIDEO1 IN (phono jacks): sensitivity 250 mV,
impedance 47 kilohms
VIDEO2 IN (phono jacks): sensitivity 250 mV,
impedance 47 kilohms
MD IN (phono jacks):
sensitivity 450 mV,
impedance 47 kilohms
impedance 47 kilohms
DVD INPUT
FRONT, REAR, CENTER, WOOFER (phono jacks):
FRONT, REAR, CENTER, WOOFER (phono jacks):
sensitivity 450 mV,
impedance 47 kilohms
impedance 47 kilohms
• The tab has been removed from the
cassette (see page 56).
• The tape has reeled to the end.
The tape does not record nor play, or there
is a decrease in sound level.
is a decrease in sound level.
• The heads are dirty. Clean them (see page
57).
• The record/playback heads are
magnetized. Demagnetize them (see page
57).
57).
The tape does not erase completely.
• The record/playback heads are
magnetized. Demagnetize them (see page
57).
57).
There is excessive wow or flutter, or the
sound drops out.
sound drops out.
• The capstans or pinch rollers are dirty.
Clean them (see page 57).
Noise increases or the high frequencies are
missing.
missing.
• The record/playback heads are
magnetized. Demagnetize them (see page
57).
57).
Tuner
Severe hum or noise (“TUNED” or
“STEREO” flashes in the display).
“STEREO” flashes in the display).
• Adjust the antenna.
• The signal strength is too weak. Connect
• The signal strength is too weak. Connect
an external antenna.
A stereo FM program cannot be received in
stereo.
stereo.
• Press STEREO/MONO so that “STEREO”
appears in the display.
If other problems not described
above occur, reset the system as
follows:
above occur, reset the system as
follows:
1 Unplug the power cord.
2 Plug the power cord back in.
3 Press c/CLOCK SET, ENTER, and
2 Plug the power cord back in.
3 Press c/CLOCK SET, ENTER, and
?
/1 at the same time.
The system is reset to the factory settings. All
the settings you made, such as the preset
stations, clock, and timer are cleared. You
should set them again.
the settings you made, such as the preset
stations, clock, and timer are cleared. You
should set them again.
continued