Sony LBT-XB800AV User Manual
52
Specifications
For the U.S. model
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
HARMONIC DISTORTION:
With 8 ohm loads, both channels driven, from
70 – 20,000 Hz; rated 80 watts per channel
minimum RMS power, with no more than
0.9% total harmonic distortion from
250 milliwatts to rated output.
70 – 20,000 Hz; rated 80 watts per channel
minimum RMS power, with no more than
0.9% total harmonic distortion from
250 milliwatts to rated output.
Center Speaker:
Continuous RMS power output (Reference)
Continuous RMS power output (Reference)
40 watts
(8 ohms at 1 kHz, 1%
THD)
(8 ohms at 1 kHz, 1%
THD)
Rear Speaker:
Continuous RMS power output (Reference)
Continuous RMS power output (Reference)
35 + 35 watts
(8 ohms at 1 kHz, 1%
THD)
(8 ohms at 1 kHz, 1%
THD)
Amplifier section
LBT-W900AV
Front Speaker:
Continuous RMS power output (Reference)
Front Speaker:
Continuous RMS power output (Reference)
100 + 100 watts
(8 ohms at 1 kHz, 10%
THD)
(8 ohms at 1 kHz, 10%
THD)
Total harmonics distortion
Less than 0.07%
(8 ohms at 1 kHz, 50 W)
(8 ohms at 1 kHz, 50 W)
Center Speaker:
Continuous RMS power output (Reference)
Continuous RMS power output (Reference)
45 watts
(8 ohms at 1 kHz, 10%
THD)
(8 ohms at 1 kHz, 10%
THD)
Rear Speaker:
Continuous RMS power output (Reference)
Continuous RMS power output (Reference)
40 + 40 watts
(8 ohms at 1 kHz, 10%
THD)
(8 ohms at 1 kHz, 10%
THD)
LBT-XB800AV
Front Speaker:
DIN power output (Rated)
Front Speaker:
DIN power output (Rated)
90 + 90 watts
(8 ohms at 1 kHz, DIN)
(8 ohms at 1 kHz, DIN)
Continuous RMS power output (Reference)
120 + 120 watts
(8 ohms at 1 kHz, 10%
THD)
(8 ohms at 1 kHz, 10%
THD)
Music power output (Reference)
200 + 200 watts
(8 ohms at 1 kHz, 10%
THD)
(8 ohms at 1 kHz, 10%
THD)
The tape does not erase completely.
•The record/playback heads are
magnetized. Demagnetize them (see page
50).
50).
There is excessive wow or flutter, or the
sound drops out.
sound drops out.
•The capstans or pinch rollers are dirty.
Clean them (see page 50).
Noise increases or the high frequencies are
missing.
missing.
•The record/playback heads are
magnetized. Demagnetize them (see page
50).
50).
Tuner
Severe hum or noise (“TUNED” or
“STEREO” flashes in the display).
“STEREO” flashes in the display).
•Adjust the antenna.
•The signal strength is too weak. Connect
•The signal strength is too weak. Connect
an external antenna.
A stereo FM program cannot be received in
stereo.
stereo.
•Press STEREO/MONO so “STEREO”
appears in the display.
If other problems not described
above occur, reset the system as
follows:
above occur, reset the system as
follows:
1 Unplug the power cord.
2 Plug the power cord back in.
3 Press
2 Plug the power cord back in.
3 Press
t/CLOCK SET, ENTER, and
1/u at the same time.
The system is reset to the factory settings. All
the settings you made, such as the preset
stations, clock, and timer are cleared. You
should set them again.
the settings you made, such as the preset
stations, clock, and timer are cleared. You
should set them again.
Troubleshooting (continued)