Sony MDS-JE480 User Manual
masterpage:Left
(3 column)
lename[C:\Documents and Settings\pc13\Desktop\MDS-JE480 PMRF\Revise
Model\J9060101_4238553151MDSJE480CEL\4238553151\GB05OPE-CEL.fm]
8
GB
model name1[MDS-JE480]
[4-238-553-15(1)]
Recording to MDs
If the MD has been partially recorded,
recording starts after the recorded tracks.
recording starts after the recorded tracks.
1
Turn on the amplifier and program
source, and select the source on the
amplifier.
source, and select the source on the
amplifier.
2
Press ?/1 to turn on the deck.
The STANDBY indicator turns off.
3
Load a recordable MD into the slot
(page 15).
(page 15).
4
Press INPUT repeatedly to select the
input jacks (connector) connected to
the program source.
input jacks (connector) connected to
the program source.
5
Press REC z.
The deck changes to recording pause.
6
Adjust the recording level if necessary.
For details, see “Adjusting the recording
level” on page 12.
level” on page 12.
7
Press
H
or
X
.
Recording starts.
8
Start playing the program source.
Operations you may want to do
during recording
1)
The track number increases by one.
Recording to an MD
When the source is
connected to the
connected to the
Set INPUT to
DIGITAL OPTICAL IN
connector
connector
D-IN
ANALOG IN jacks
A-IN
To
Press
Stop recording
x
Pause recording
X
Resume recording after
pausing
pausing
1)
H or X
Eject the MD
EJECT A after stopping
recording
recording
To change the display while
recording
Press LEVEL/DISPLAY/CHAR (or DISPLAY)
repeatedly to change the display.
repeatedly to change the display.
Each time you press the button, the display
changes cyclically as follows:
Track number and recorded time of the current
track
changes cyclically as follows:
Track number and recorded time of the current
track
t Remaining recordable time
2)
on the
MD
t Level of the input signal t Track
name
3)
2)
Time shown in the display differs depending on
the setting of REC MODE.
the setting of REC MODE.
3)
“No Name” appears when the track has no name.
After recording
Press EJECT A to remove the MD or press
?/1 to turn off the deck.
“TOC” or “TOC Writing” starts flashing. The
TOC is updated and recording is completed.
?/1 to turn off the deck.
“TOC” or “TOC Writing” starts flashing. The
TOC is updated and recording is completed.
Before disconnecting the AC power
cord
MD recording is completed when the MD Table
of Contents (TOC) is updated. The TOC is
updated when you eject the MD or press ?/1 to
turn off the deck. Do not disconnect the AC
power cord before updating the TOC (while
“TOC” is lit) or while updating the TOC (while
“TOC Writing” is flashing) to ensure a
complete recording.
of Contents (TOC) is updated. The TOC is
updated when you eject the MD or press ?/1 to
turn off the deck. Do not disconnect the AC
power cord before updating the TOC (while
“TOC” is lit) or while updating the TOC (while
“TOC Writing” is flashing) to ensure a
complete recording.
Automatic conversion of digital
sampling rates
A built-in sampling rate converter automatically
converts the sampling frequency of various
digital sources to the 44.1 kHz sampling rate of
the MD deck. This allows you to monitor and
record sources such as 32 or 48 kHz DAT tape
or satellite broadcasts, as well as the CDs and
MDs.
converts the sampling frequency of various
digital sources to the 44.1 kHz sampling rate of
the MD deck. This allows you to monitor and
record sources such as 32 or 48 kHz DAT tape
or satellite broadcasts, as well as the CDs and
MDs.
Notes on recording