Sony MEX-BT2700 User Manual
14
D:\Documents and Settings\takashi-shimomura\Desktop\DTP\848626S MEX-
BT2700(U)\4125798111_MEX-BT2700(U)_CaFR\01US02CD-U.fm
BT2700(U)\4125798111_MEX-BT2700(U)_CaFR\01US02CD-U.fm
masterpage:Left
MEX-BT2700
4-125-798-11 (1)
Bluetooth function
Bluetooth operations
To use the Bluetooth function, the following
procedure is necessary.
procedure is necessary.
1
Pairing
When connecting Bluetooth devices for the
first time, mutual registration is required. This
is called “pairing.” This registration (pairing)
is required only for the first time, as this unit
and the other devices will recognize each
other automatically from the next time. You
can pair up to 8 devices. (Depending on the
device, you may need to input a passcode for
each connection.)
When connecting Bluetooth devices for the
first time, mutual registration is required. This
is called “pairing.” This registration (pairing)
is required only for the first time, as this unit
and the other devices will recognize each
other automatically from the next time. You
can pair up to 8 devices. (Depending on the
device, you may need to input a passcode for
each connection.)
2
Connection
To use the device after pairing is made, start
the connection. Sometimes pairing allows to
connect automatically.
To use the device after pairing is made, start
the connection. Sometimes pairing allows to
connect automatically.
3
Handsfree calling/Music streaming
You can talk handsfree and listen to music
when the connection is made.
You can talk handsfree and listen to music
when the connection is made.
Pairing
First, register (“pair”) a Bluetooth device
(cellular phone, etc.) and this unit with each
other. You can pair up to 8 devices. Once pairing
is established, there is no need for pairing again.
(cellular phone, etc.) and this unit with each
other. You can pair up to 8 devices. Once pairing
is established, there is no need for pairing again.
1
Place the Bluetooth device within 1 m
(3 ft) of this unit.
(3 ft) of this unit.
2
Press and hold (BT) until “
” flashes
(about 5 seconds).
The unit enters pairing standby mode.
The unit enters pairing standby mode.
3
Set the Bluetooth device to search for
this unit.
A list of detected devices appears in the
display of the device to be connected. This
unit is displayed as “XPLOD” on the device
to be connected.
this unit.
A list of detected devices appears in the
display of the device to be connected. This
unit is displayed as “XPLOD” on the device
to be connected.
4
If Passcode* input is required on the
display of the device to be connected,
input “0000.”
display of the device to be connected,
input “0000.”
This unit and the Bluetooth device memorize
each other’s information, and when pairing is
made, the unit is ready for connection to the
device.
each other’s information, and when pairing is
made, the unit is ready for connection to the
device.
“
” flashes and then stays lit after pairing is
complete.
5
Set the Bluetooth device to connect to
this unit.
“
this unit.
“
” or “
” appears when the connection is
made.
* Passcode may be called “passkey,” “PIN code,” “PIN
number” or “Password,” etc., depending on the
device.
device.
Note
Pairing standby mode is not released until the
connection is made.
Pairing standby mode is not released until the
connection is made.
About Bluetooth icons
The following icons are used by this unit.
Support site
http://esupport.sony.com
http://www.xplodsony.com/
http://www.xplodsony.com/
flashing
lit:
flashing:
off:
flashing:
off:
Bluetooth signal on
Pairing standby mode
Bluetooth signal off
Pairing standby mode
Bluetooth signal off
lit:
flashing:
off:
flashing:
off:
Connection successful
Connecting
No connection
Connecting
No connection
lit:
flashing:
off:
flashing:
off:
Connection successful
Connecting
No connection
Connecting
No connection
XXXXXXX
DR-BT30Q
XPLOD
XXXX
Input passcode.
“0000”