Sony MKS-2010 User Manual
170
Other Settings
Ch
a
a
p
te
r
9
Sys
te
m
Set
tin
gs
gs
• Press directry on the list in the status area.
• Use the arrow buttons to scroll the reverse video
• Use the arrow buttons to scroll the reverse video
cursor.
• Turn the knob.
a) Setting values 5 to 8 are valid only when the MKS-2110M (option)
is installed.
The selected output port number appears in reverse
video.
video.
3
Press the button for the marker that you want to set
(multiple selections possible).
(multiple selections possible).
Box1: Box marker 1
Box2: Box marker 2 (adjustable luminance)
Cross: Cross marker
Box2: Box marker 2 (adjustable luminance)
Cross: Cross marker
If you select Box1 or Box2, a popup window opens so
that you can select the aspect ratio. You can also set the
aspect ratio by turning the knobs. If you select Cross,
the cross marker is turned on.
that you can select the aspect ratio. You can also set the
aspect ratio by turning the knobs. If you select Cross,
the cross marker is turned on.
To select the aspect ratio
In the popup window, press the button for the aspect ratio
that you want.
• 16:9
• 14:9
• 4:3
In the popup window, press the button for the aspect ratio
that you want.
• 16:9
• 14:9
• 4:3
To set other marker parameters
Turn the knobs to adjust the following parameters.
Turn the knobs to adjust the following parameters.
• When Box1 was selected:
• When Box2 was selected:
Utility Settings (Utility Menu)
You can assign utility commands to the buttons in the
utility control block.
utility control block.
Assigning utility commands
1
From the top menu, select Setup/Diag >Operation
>Utility.
>Utility.
The Utility menu appears. The “Assign” list of
currently assigned utility commands appears at the left
of the status area. The “Utility Command” list of all
assignable utility commands appears at the right of the
status area.
currently assigned utility commands appears at the left
of the status area. The “Utility Command” list of all
assignable utility commands appears at the right of the
status area.
The status area displays abbreviated utility command
names. See the next section “Utility command list” for
a list of these abbreviated names.
names. See the next section “Utility command list” for
a list of these abbreviated names.
2
Press [Block Sel].
A popup window appears.
3
Select the group of operation buttons to which you
want to assign a utility command.
want to assign a utility command.
Device/Utility: DEVICE/UTILITY operation buttons
Enable/Utility: ENABLE/UTILITY operation
Enable/Utility: ENABLE/UTILITY operation
buttons
4
In the “Assign” list, select the button to which you
want to assign the command.
want to assign the command.
• Press directry on the list in the status area.
• Use the arrow buttons to scroll the reverse video
• Use the arrow buttons to scroll the reverse video
cursor.
• Turn the knob.
a) When Device/Utility is selected
b) Enable/Utility is selected
b) Enable/Utility is selected
5
In the “Utility Command” list, do any of the following
to select the command to assign to the selected button.
to select the command to assign to the selected button.
• Press directry on the list in the status area.
• Use the arrow buttons to scroll the reverse video
• Use the arrow buttons to scroll the reverse video
cursor.
• Turn the knobs.
Knob
Description
Setting values
1 (No)
Output port number selection 1 to 8
a)
Knob
Description
Setting values
2 (Size)
Size of box
50.00 to 100.00
Knob
Description
Setting values
2 (Size)
Size of box
50.00 to 100.00
3 (Luminance)
Luminance of displayed
color
color
0.00 to 100.00
Knob
Description
Setting values
1 (No)
Button number selection
1 to 9
a)
1 to 4
b)