Sony MPK-THA User Manual

Page of 2
Troubleshooting
Symptom
There are drops of water
inside the marine pack.
The recording and playing
back function does not work.
Specifications
Material
Plastic (PC, ABS), stainless steel, glass
Water-resistance
O-ring, buckle
Pressure-resistance
To a depth of up to 40 m (132 feet) underwater
Switches that can be externally operated
Power, Mode, Shutter, Zoom, Flash, Macro, Control, Self-timer, Review,
Menu, Image Size/Delete
Dimension
Approx. 135 
×
 96 
×
 55 mm (5 3/8 
×
 3 7/8 
×
 2 1/4 inches) (w/h/d)
(excluding projecting parts)
Mass
Approx. 280 g (9.8 oz) (marine pack only)
Supplied accessories
Hand strap (1)
Grease (1)
O-ring (1)
O-ring remover (1)
Spacer (1)
Operating Instructions (1)
O-ring Maintenance Manual (1)
Optional accessories
Color filter VF-MPTH
Arm kit VCT-MP1K
Underwater video light HVL-ML20M (must be used together with arm kit
VCT-MP1K, “InfoLITHIUM” (M series) battery pack and M series battery
charger)
Design and specifications subject to change without notice.
Marine Pack
3-086-870-11(1)
MPK-THA
© 2003 Sony Corporation  Printed in Japan
E
Operating Instructions
Mode d’emploi
Manual de instrucciones
Gebruiksaanwijzing
English
Français
Main Feature
Useable at a depth of up to 40 m (132 feet) underwater.
•This marine pack MPK-THA is exclusively for use with the Sony Digital
Still Camera DSC-T1. (Cyber-shot for this marine pack is not available in
all countries.)
•This marine pack is water-resistant, enabling the digital still camera to be
used in the rain or snow or at the beach.
A loose or nipped O-ring, or sand or dirt on the O-ring may cause
water leaks under water.
Be sure to check the O-ring before use.
For details, read the O-ring Maintenance Manual.
Notice
•Before using the digital still camera underwater, first take the marine pack
to a depth of about 1 m (3.3 feet) and check that the digital still camera is
operating properly and that the marine pack is not leaking, then
commence your dive.
•In the unlikely event that a malfunction of the marine pack causes damage
due to water leakage, Sony does not guarantee against damages to the
equipment contained in it (digital still camera, battery, etc.) and the
recorded contents, nor expenses entailed in the photography.
Precautions
•When using this marine pack while diving, be sure to pay attention to the
surrounding situation. Lack of attention may cause an accident while
diving.
•In case a water leakage is occurred, be sure to pay attention to the
surrounding situation and surface following the safety rules for diving.
•Do not subject the front glass to strong shock, as it may crack.
•Avoid opening the marine pack at the beach or on the water. Preparation
such as installing the digital still camera and changing the “Memory Stick
Duo”/“Memory Stick PRO Duo” should be done in a place with low
humidity and no salty air.
•Do not throw the marine pack into the water.
•Avoid using the marine pack in places with strong waves.
•Avoid using the marine pack under the following situations:
– in a very hot or humid place.
– in water hotter than 40 ˚C (104 ˚F).
– at temperatures lower than 0 ˚C (32 ˚F).
In these situations moisture condensation or water leakage may occur and
damage the equipment.
•Use the marine pack for no longer than 30 minutes at a time in
temperatures above 35 ˚C (95 ˚F).
•Do not leave the marine pack under direct sunlight in a very hot and
humid place for a long period of time. If you cannot avoid leaving the
marine pack under direct sunlight, be sure to cover the pack with a towel
or other protection.
•The digital still camera heats up if it is used inside the marine pack for a
long time. Before removing the digital still camera from the marine pack,
leave the marine pack in the shade or other cool place for a while to cool
down.
If sun oil is on the marine pack, be sure to wash it off thoroughly using
lukewarm water. If the marine pack is left with sun oil on its body, the
surface of the marine pack may become discolored or damaged. (such
as cracks on the surface.)
Water leakage
If water happens to leak in, stop exposing the marine pack to water
immediately.
If the digital still camera gets wet, take it to the nearest Sony dealer
immediately. Repair costs must be borne by the customer.
Anti-fogging effect
Front glass of the marine pack has anti-fogging effect, however install the
digital still camera in a low-humidity room or a similar environment.
O-ring
This equipment uses an O-ring to maintain its water resistance. For details,
refer to the separate O-ring Maintenance Manual.
Improper handling of the O-ring can result in water leakage.
Drip-proof packing
Do not remove or apply grease to the drip-proof packing. If the packing
rises up or is nipped, this may result in water leaks.
Grease
Use the grease in the blue tube (supplied). Using the grease in the yellow
tube or other manufacturer’s grease will damage the O-ring, and cause
water leaks.
O-ring and grease
You can obtain O-rings and grease at your nearest Sony dealer.
O-ring (model No. 3-080-065-01)
Grease (model No. 3-071-370-01)
O-ring and drip-proof packing serviceable life
The serviceable life of O-rings and drip-proof packing varies with the
frequency of use of the marine pack and storage conditions. Generally, the
serviceable life of the parts is about one year.
When replacing the drip-proof packing, take it to your nearest Sony dealer.
Repair costs must be borne by the customer.
Maintenance
After recording
•After recording in a location subject to sea breezes, wash the marine pack
with fresh water to remove salt and sand with the buckles fastened
thoroughly, then wipe with a soft dry cloth. It is recommended that you
submerge the marine pack in fresh water for about 30 minutes. If it is left
with salt on it, metal portions may be damaged or rust may form and
cause water leakage.
•If sun oil is on the marine pack, be sure to wash it off thoroughly using
lukewarm water.
•Clean the inside of the marine pack with a soft dry cloth. Do not wash the
inside of the marine pack.
Be sure to perform the above maintenance each time you use the marine
pack. Do not use any type of solvent such as alcohol, benzine or thinner for
cleaning, as this might damage the surface finish of the marine pack.
When storing the marine pack
•Attach the spacer supplied with your marine pack to prevent wear of the
O-ring. (See illustration A)
•Prevent dust from collecting on the O-ring.
•Lightly coat the O-ring with grease and insert it into the seating groove,
then store the marine pack in a cool, well-ventilated location. Do not
fasten the buckle.
•Avoid storing the marine pack in a cold, very hot or humid place, or
together with naphthalene or camphor, as these conditions might damage
the unit.
Preparation
Preparing the digital still camera
Install the digital still camera in a low-humidity room or a similar
environment.
Opening or closing the marine pack in hot or humid locations may result in
fogging of the front glass.
For details, refer to the operating instructions supplied with your digital
still camera.
1 Remove the hand strap from the digital still camera.
2 Install the battery pack.
Be sure to use a fully charged battery pack.
3 Insert the “Memory Stick Duo”/“Memory Stick PRO Duo”.
4 Open the lens cover and turn on the POWER of the digital still
camera.
When you open the lens cover, be careful not to touch the lens.
5 Turn on the LCD screen.
If the Mode switch on the digital still camera is set to 
 when you open the lens
cover to turn on the power, the LCD screen turns on.
6 Set each of the settings on the digital still camera to AUTO
mode.
7 Set the AF illuminator on the digital still camera to OFF.
This disables use of the AF illuminator.
Make sure the lens and LCD screen of the digital still camera are not dirty.
Installing the digital still camera inside the
marine pack
1 Turn off the POWER of the digital still camera.
2 Set the Mode switch of the digital still camera to 
. (C-1)
3 Open the marine pack. (C-2)
Press the top and bottom OPEN buttons at once 1 and release the buckle in the
direction of the arrow 2 to open the marine pack body.
Note
Take care not to lose the spacer as you will need it to store the marine pack.
4 Prepare the marine pack.
Be sure to read the separate O-ring Maintenance Manual.
Important details regarding handling of the O-ring are described in this
manual.
1
Use the O-ring remover (supplied) to remove the O-ring.
2
Coat the O-ring with grease.
Clean off any sand or dirt on the O-ring, in the seating groove, or on the marine
pack’s body where it touches the O-ring. Coat the O-ring with a light, even
layer of grease.
3
Check the drip-proof packing for any sand or dirt.
Notes
• Do not remove the drip-proof packing or coat the drip-proof packing with
grease.
• The marine pack’s body may be scratched or water may leak if the cover is
closed with sand or dirt on the O-ring or drip-proof packing.
5 Set the Mode dial of the marine pack to the position shown in
C-3.
6 Install the digital still camera inside the marine pack. (C-4)
When installing the marine pack, leave the lens cover of the digital still
camera open. Forcing the marine pack closed while the lens cover is closed
can lead to a malfunction. Check to see if the digital still camera is inserted
correctly or not.
Check that the digital still camera is placed correctly.
7 Close the marine pack’s body and fasten the buckle. (C-5)
Secure the marine pack’s body, and fasten the buckle until it clicks.
Buckle position when closing the marine pack’s body
Good example (See illustration C-5 1)
Bad example (See illustration C-5 2)
If you close the buckle as shown in C-5 2, the buckle will be caught,
making it impossible to lock the marine pack.
Note
When closing the marine pack’s body, make sure that there is no debris, sand,
hair, or any other foreign matter on the O-ring or in the seating groove. Water
leakage may result if any such foreign matter is caught in these places.
D Attach the hand strap
We recommend attaching the hand strap (supplied) before using the marine
pack. The length of the hand strap can be regulated. (See illustration D-1)
Note
Be careful not to pinch the hand strap when you open and close the marine
pack body. Water may leak in if you do.
Using the Marine Pack
Recording
1 Set the POWER button to ON. (E-1)
Check that the Mode dial operates normally.
The mode is changed with the mode dial.
For details of each mode, check in the LCD screen.
2 Set the Mode dial to the desired mode and press the shutter
button. (E-2, 3)
You can record pictures while looking at the LCD screen.
To record still images, set the Mode switch of the digital still camera to 
.
To record moving images, set the Mode switch of the digital still camera to 
.
To record pictures in the various scene, set the Mode switch of the digital still
camera to 
, and select the desired mode of the MENU button.
Sound cannot be recorded while recording moving images.
Notes
•Do not rotate the Mode dial of the digital still camera in the marine pack
excessively. It may cause trouble.
•Since the refractive index underwater is higher than that in air, objects
appear 1/4 closer. Therefore when recording underwater with focus
preset, the distance you set and actual distance to the objects is different.
•Dust or debris on the glass surface inside the marine pack may be focused
on in the digital still camera’s “Magnifying glass mode”.  In that event,
remove the dust or debris on the glass surface.
•For details, refer to the operating instructions supplied with your digital
still camera.
F Using/Setting various functions
You can use the various functions of the digital still camera DSC-T1
installed in the marine pack.
G Use the zoom
Press the zoom button.
1
Press on the W side for wide-angle. (Subject appears farther away.)
2
Press on the T side for telephoto. (Subject appears closer.)
Notes
•You cannot record images while looking through the finder.
•If you do not record images for over three minutes, the digital still camera
turns off automatically to prevent the battery from wearing down. To use
the digital still camera again, set the POWER button to ON again.
Playing back with the control button
You can play back images on the LCD screen using the control button. You
cannot hear the sound.
1 Set the POWER button to ON. (H-1)
2 Set the Mode dial to 
. (H-2)
3 Select the desired image with the control button. (H-3)
H-3 1 To previous image
H-3 2 To next image
For details, refer to the operating instructions supplied with your digital still
camera.
Removing the digital still camera
1 Set the POWER button to OFF. (I-1)
2 Press the top and bottom OPEN buttons at once 
1 and release
the buckle in the direction of the arrow 2 to open the marine
pack body. (
I-2)
3 Remove the digital still camera from the marine pack.
When the digital still camera has been used for a long time, the digital still camera
heats up. Turn the power off and leave for a while to cool down before removing it
from the marine pack.
Be careful not to drop the digital still camera when removing it.
Note
Before opening the marine pack, rinse it with tap water or fresh water and
then wipe the water off with a soft cloth. When opening it, be careful not to
let any water from your body, hair, or wetsuit cuffs drip onto the digital
still camera.
Before making a dive
•Before recording images underwater, first take the marine pack to a depth
of about 1m (3.3 feet) and check that it operates properly and is not
leaking, then commence your dive.
•Install the digital still camera in the marine pack before diving, and avoid
opening and closing the marine pack while on board boats or at the
seashore as much as possible. When installing the digital still camera, do it
in a place that has as low a humidity as possible.
•Before using the marine pack, make sure that no debris has been caught
between the front and back halves of the marine pack’s body.
•In images recorded underwater, the subject sometimes has a bluish cast.
To correct the colour when this happens, use the colour filter VF-MPTH
(optional).
Times that are suited for recording
The most suitable time for recording images is between 10:00 AM and 2:00
PM, when the sun is directly overhead.
To record pictures in places where the sunlight does not reach well or at
night, please use the underwater video light HVL-ML20M (optional).
B
C
F
I
1
2
5
1
1
Shutter button
Déclencheur
Mode dial
Sélecteur de
Mode  (MODE)
Front glass
Verre avant
Buckle
Fermoir
Spacer (remove to use the
marine pack)
Entretoise (à retirer avant
d’utiliser le Marine Pack)
D
G
Cause/Corrective Actions
• The buckle is not fastened.
b Fasten the buckle until it clicks.
• The O-ring is not set correctly.
b Place the O-ring evenly in the groove.
• There are scratches or cracks on the O-ring.
b Replace the O-ring with a new one.
• The battery pack has run out.
b Charge the battery pack fully.
• The “Memory Stick Duo”/“Memory Stick
PRO Duo” is full.
b Insert another “Memory Stick Duo”/
“Memory Stick PRO Duo” or erase
unneeded data from the “Memory Stick
Duo”/“Memory Stick PRO Duo.”
• The write-protect tab on the “Memory Stick
Duo”/“Memory Stick PRO Duo” is set to
LOCK.
b Set the tab to the recording position or
insert a new “Memory Stick Duo”/
“Memory Stick PRO Duo.”
Caractéristique principale
Utilisable jusqu’à une profondeur de 40 mètres (132 pieds) sous
l’eau.
•Le caisson étanche MPK-THA est conçu spécialement pour l’appareil
photo numérique Sony DSC-T1. (Le Cyber-shot pour lequel ce caisson a
été conçu n’est pas commercialisé dans tous les pays.)
•Ce caisson est étanche à l’eau, ce qui permet d’utiliser l’appareil photo
numérique sous la pluie ou la neige ou au bord de la plage.
Un joint torique relâché ou pincé ou la présence de sable ou de saletés
sur le joint peut entraîner des infiltrations d’eau.
Vérifiez le joint torique avant d’utiliser l’équipement. Pour plus
d’informations, reportez-vous  au Mode d’emploi du joint torique.
Avertissement
•Avant de plonger pour une prise de vues sous-marine, immergez le
Marine Pack à 1 mètre (3,3 pieds) sous l’eau environ et assurez-vous que
l’eau ne s’infiltre pas à l’intérieur et que l’appareil photo numérique
fonctionne correctement.
•Dans le cas très improbable où une anomalie du Marine Pack causerait
des dommages dus à une infiltration d’eau, notez que la garantie Sony ne
couvre pas les dommages subis par le matériel (appareil photo
numérique, batterie, etc.) à l’intérieur du Marine Pack, le contenu
enregistré ou les frais encourus pour la prise de vues.
Précautions
•Lorsque vous utilisez le caisson étanche pour la plongée, faites attention à
l’environnement. Un manque d’attention peut être à l’origine d’un
accident pendant la plongée.
•En cas d’infiltration d’eau, faites attention à l’environnement et remontez
à la surface en respectant les règles de plongée.
•Ne soumettez pas le verre avant à des chocs importants car il pourrait se
fendre.
•N’ouvrez pas le Marine Pack sur la plage ou dans l’eau. Les opérations
préparatoires telles que la mise en place de l’appareil photo numérique et
le changement de « Memory Stick Duo »/« Memory Stick PRO Duo »
doivent être effectuées à l’abri de l’humidité et de l’air salin.
•Ne jetez pas le Marine Pack dans l’eau.
•N’utilisez pas le Marine Pack par fortes vagues.
•N’utilisez pas le Marine Pack dans les conditions suivantes :
– dans un endroit très chaud ou humide,
– dans de l’eau chaude à plus de 40 °C (104 °F),
– à des températures inférieures à 0 °C (32 °F).
Dans de telles conditions, le matériel pourrait être endommagé par une
condensation d’humidité ou une infiltration d’eau.
•N’utilisez pas le Marine Pack plus de 30 minutes d’affilée par une
température supérieure à 35 °C (95 °F).
•Ne laissez pas longtemps le Marine Pack en plein soleil dans un endroit
très chaud et humide. Si vous ne pouvez éviter de le laisser au soleil,
recouvrez-le d’une serviette ou d’une autre protection.
•L’appareil photo numérique s’échauffe s’il est utilisé pendant longtemps à
l’intérieur du Marine Pack. Avant d’en retirer l’appareil photo, laissez
temporairement le Marine Pack à l’ombre ou dans un endroit frais pour
qu’il se refroidisse.
S’il y a de la crème solaire sur le Marine Pack, prenez soin de l’éliminer
convenablement avec de l’eau tiède. Si la surface du boîtier du Marine
Pack est souillée avec de la crème solaire, elle risque d’en être
décolorée et endommagée. (craquelures sur la surface)
Infiltration d’eau
Si de l’eau s’infiltre dans le Marine Pack, arrêtez immédiatement de
l’exposer à l’eau.
Si l’appareil photo numérique est mouillé, portez-le immédiatement chez le
revendeur Sony le plus proche. Les frais de réparation seront à la charge de
l’utilisateur.
Effet antigel
Le verre avant du Marine Pack a un effet antibuée mais il est préférable de
préparer l'appareil photo numérique dans une pièce peu humide ou un
environnement similaire.
Joint torique
L’équipement utilise un joint torique pour garantir son étanchéité. Pour
plus d’informations, reportez-vous au Mode d’emploi séparé du joint
torique.
Une manipulation inadéquate du joint torique peut entraîner une
infiltration d’eau.
Garniture pare-gouttes
Ne retirez pas et ne placez pas de graisse sur la garniture pare-gouttes car
ceci pourrait entraîner une saillie de la garniture hors du boîtier ou son
pincement.
Graisse
Utilisez la graisse du tube bleu (fourni). L’emploi de la graisse du tube
jaune ou d’une graisse d’un autre fabricant endommagerait le joint torique
et entraînerait des infiltrations d’eau.
Joint torique et graisse
Vous pouvez vous procurer des joints toriques et de la graisse pour objectif
chez votre revendeur Sony.
Joint torique (No. de modèle : 3-080-065-01)
Graisse (No. de modèle : 3-071-370-01)
Durée de service du joint torique et de la garniture pare-
gouttes
La durée de service du joint torique et de la garniture pare-gouttes varie
selon la fréquence d’utilisation du Marine Pack et les conditions
d’entreposage. Elle est généralement d’une année environ.
Pour le remplacement de la garniture pare-gouttes, apportez le Marine Pack
chez votre revendeur Sony.
Les frais de réparation seront à la charge de l’utilisateur.
Entretien
Après la prise de vues
•Après une prise de vues dans un endroit soumis à la brise marine, lavez le
Marine Pack à l’eau douce avec les fermoirs correctement verrouillés pour
en faire partir le sel et le sable, puis essuyez-le avec un chiffon doux et sec.
Il est recommandé de plonger le Marine Pack dans de l’eau douce
pendant 30 minutes environ. Ne laissez pas de sel dessus car il pourrait
attaquer les parties métalliques et de la rouille risquerait de se former et
de causer une infiltration d’eau.
•S’il y a de la crème solaire sur le Marine Pack, prenez soin de l’éliminer
convenablement avec de l’eau tiède.
•Ne lavez pas l’intérieur du Marine Pack, mais nettoyez-le avec un linge
doux et sec.
Effectuez les opérations d’entretien ci-dessus après chaque utilisation du
Marine Pack. N’utilisez aucune sorte de solvant, tel qu’alcool, benzine ou
diluant pour le nettoyage car ces substances peuvent attaquer la finition du
Marine Pack.
Lors du stockage du Marine Pack
•Posez l’entretoise fournie avec le Marine Pack pour protéger le joint
torique contre l’usure. (Voir l’illustration A)
•Empêchez l’accumulation de poussière sur le joint torique.
•Passez une légère couche de graisse sur le joint torique et insérez-le dans
la gorge du boîtier. Rangez ensuite le Marine Pack dans un endroit frais et
bien aéré. Ne verrouillez pas le fermoir.
•Ne rangez pas le Marine Pack dans un endroit froid, très chaud ou
humide ou avec de la naphtaline ou du camphre. Ceci pourrait
l’endommager.
Préparation
Préparation de l’appareil photo numérique
Installez l’appareil photo numérique autant que possible dans un endroit peu
humide En effet, l’ouverture et/ou  la fermeture du Marine Pack dans un
endroit chaud ou humide provoquerait de la buée sur le verre avant.
Pour plus d’informations, reportez-vous au mode d’emploi, fourni avec
l’appareil photo numérique.
1 Retirez la sangle de l'appareil photo numérique.
2 Mettez la batterie en place.
Utilisez une batterie complètement chargée.
3 Insérez le « Memory Stick Duo»/« Memory Stick PRO Duo».
4 Ouvrez le cache-objectif et mettez l’appareil photo numérique
sous tension.
Lorsque vous ouvrez le cache-objectif, veillez à ne pas toucher l’objectif.
5 Allumez l’écran LCD.
Si le sélecteur de mode de l'appareil photo numérique est réglé sur 
 lorsque
vous ouvrez le cache-objectif pour mettre l'appareil sous tension, l'écran s’allume.
6 Réglez toutes les fonctions de l’appareil photo numérique en
mode automatique.
7 Mettez hors service (OFF) l’éclairage AF de l’appareil photo
numérique.
L’éclairage AF est ainsi invalidé.
Assurez-vous que l’objectif et l’écran LCD de l’appareil photo numérique ne sont
pas sales.
Mise en place de l’appareil photo
numérique
1 Mettez l’appareil photo hors tension (par le commutateur
POWER).
2 Placez le sélecteur de mode de l’appareil photo sur 
. (C-1)
3 Ouvrez le Marine Pack. (C-2)
Appuyez en même temps sur les touches OPEN supérieure et inférieure 1 pour
libérer le fermoir dans le sens de la flèche 2 et ouvrir le coffret du Marine Pack.
Remarque
Prenez soin de ne pas perdre l’entretoise car elle sera nécessaire lors du rangement
du Marine Pack.
4 Préparez le Marine Pack.
Veillez à lire le Mode d’emploi séparé du joint torique, car il renferme des
informations importantes sur la manipulation du joint torique.
1
Servez de l’extracteur de joint torique (fourni) pour déposer le joint.
2
Enduisez le joint torique avec de la graisse.
Enlevez le sable et les autres saletés sur le joint torique, sur la gorge du joint ou
sur la surface du boîtier entrant en contact avec le joint torique. Enduisez le joint
torique d’une légère couche uniforme de graisse.
3
Assurez-vous que la garniture pare-gouttes est exempte de sable et de saletés.
Remarques
• Ne retirez pas la garniture pare-gouttes et ne l’enduisez pas avec de la graisse.
• Le boîtier risque d’être griffé et de l’eau pourrait s’infiltrer si le couvercle est
refermé alors que du sable ou de la saleté se trouve sur le joint torique ou sur
la garniture pare-gouttes.
5 Réglez le sélecteur Mode du Marine Pack à la position indiquée
en C-3.
6 Installez l’appareil photo numérique dans le Marine Pack. (C-4)
Lorsque vous installez l’appareil dans le Marine Pack, laissez le cache-
objectif de l’appareil photo numérique ouvert. Si vous essayez de fermer le
Marine Pack alors que le cache est fermé, un problème peut apparaître.
Vérifiez si l’appareil photo numérique est inséré ou non correctement.
Assurez-vous que l’appareil photo est correctement disposé.
7 Fermez le boîtier latéral et bouclez le fermoir. (C-5)
Immobiliser le boîtier latéral et bouclez le fermoir jusqu’à ce qu’il se verrouille.
Position du fermoir à la fermeture du boîtier latéral
Position correcte (Voir l’illustration C-5 1)
Position incorrecte (Voir l’illustration C-5 2)
Si vous bouclez le fermoir comme illustré en C-5 2, il sera coincé, ce qui
rendra difficile la fermeture du Marine Pack.
Remarque
Lorsque vous refermez le Marine Pack, assurez-vous qu’il n’y a pas de saletés,
sable, cheveux ou autres corps étrangers sur le joint torique ou dans la gorge du
boîtier. Ceci pourrait provoquer une infiltration d’eau.
D
 Attachez la sangle
Il est conseillé d’attacher la sangle (fournie) avant d’utiliser le Marine Pack.
La longueur de la sangle peut être ajustée. (Voir l’illustration D-1)
Remarque
Attention de ne pas coincer la sangle lorsque vous ouvrez ou fermez le
caisson. De l’eau risque sinon de s’infiltrer à l’intérieur.
Utilisation du Marine Pack
Prise de vues
1 Réglez la touche POWER sur ON. (E-1)
Assurez-vous que le sélecteur de mode fonctionne normalement.
Le mode se change avec le sélecteur de mode.
Pour les détails sur chaque mode, consultez l’écran LCD.
2 Réglez le sélecteur Mode à la position appropriée et appuyez
sur le déclencheur. (E-2, 3)
Vous pouvez enregistrer des images en regardant l’écran LCD.
Pour enregistrer des images fixes, réglez le sélecteur de mode de l’appareil photo
numérique sur 
 .
Pour enregistrer des images animées, réglez le sélecteur de mode de l’appareil
photo numérique sur 
.
Pour filmer des scènes variées, réglez le sélecteur de mode de l’appareil photo sur
 et sélectionnez le mode souhaité de la touche MENU.
Il n’est pas possible d’enregistrer des sons en même temps que des images
animées.
Remarques
•Ne pas faire trop tourner le sélecteur de mode de l’appareil photo
numérique dans le Marine Pack trop longtemps pour ne pas
l’endommager.
•Comme l’indice de réfraction de l’eau est supérieur à celui de l’air, les
objets apparaissent 1/4 plus gros. C’est pourquoi si vous filmez avec une
mise au point fixe, la distance réelle du sujet sera différente de la distance
préréglée.
•En mode « modo loupe », la mise au point peut se faire sur la poussière ou
les saletés présentes sur le verre à l’intérieur du Marine Pack. Il est donc
conseillé de bien nettoyer la surface du verre.
•Pour plus d’informations, consultez le mode d’emploi de l’appareil photo
numérique.
F
 Réglage / Utilisation des diverses fonctions
Vous pouvez utiliser les diverses fonctions de l’appareil photo numérique
DSC-T1 alors qu’il est installé dans le Marine Pack.
G
 Utilisation du zoom
Appuyez sur la touche de zoom.
1
Appuyez sur le côté W pour une prise de vues au grand angle. (Le sujet
s’éloigne.)
2
Appuyez sur le côté T pour une prise de vues au téléobjectif. (Le sujet
s’approche.)
Remarques
•Il n’est pas possible d’enregistrer des images en regardant par le viseur.
•Si vous n’utilisez pas l’appareil photo numérique pendant plus de trois
minutes lors d’une prise de vues, il s’éteint automatiquement pour
économiser la batterie. Pour utiliser de nouveau l’appareil photo
numérique, réglez de nouveau la touche POWER sur ON.
Lecture avec la touche de commande
Vous pouvez visionner les images sur l’écran LCD à l’aide de la touche de
commande. Il n’y a pas de son.
1 Réglez la touche POWER sur ON. (H-1)
2 Réglez le sélecteur Mode sur 
. (H-2)
3 Sélectionnez l’image souhaitée par la touche de commande.
(H-3)
H-3 1 Vers l’image précédente
H-3 2 Vers l’image suivante
Pour plus d’informations, consultez le mode d’emploi de l’appareil photo
numérique.
Retrait de l’appareil photo numérique
1 Réglez la touche POWER sur OFF. (I-1)
2 Appuyez en même temps sur les touches OPEN supérieure et
inférieure 1 pour libérer le fermoir dans le sens de la flèche 2
et ouvrir le coffret du Marine Pack. (I-2)
3 Retirez l’appareil photo numérique hors du Marine Pack.
Lorsque l’appareil photo numérique a fonctionné pendant longtemps, il est
relativement chaud. Mettez-le hors tension et laissez-le se refroidir pendant un
certain temps avant de le retirer du Marine Pack.
Veillez à ne pas faire tomber l’appareil en le retirant.
Remarque
Avant d’ouvrir le Marine Pack, rincez-le avec de l’eau du robinet ou de
l’eau douce, puis essuyez-le complètement avec un chiffon doux. Lorsque
vous l’ouvrez, veillez à ne pas le mouiller avec l’eau de votre combinaison
de plongée, de vos cheveux ou de votre corps.
Avant de partir en plongée
•Avant de partir faire de la photographie sous-marine, immergez le Marine
Pack à 1 mètre (3,3 pieds) sous l’eau environ et assurez-vous qu’il
fonctionne correctement et que de l’eau ne s’infiltre pas à l’intérieur.
•Installez l’appareil photo numérique dans le Marine Pack avant la plongée
et, autant que possible, évitez de l’ouvrir et de le fermer à bord d’un
bateau ou sur la plage. Installez l’appareil dans le Marine Pack dans un
endroit aussi peu humide que possible.
•Avant d’utiliser le Marine Pack, assurez-vous qu’il n’y a pas de saletés
coincées entre les moitiés avant et arrière du boîtier.
•Sur des images prises sous l’eau, le sujet présente parfois une dominante
bleuâtre. Pour corriger ce phénomène, utilisez le filtre couleur
VF-MPTH (en option), disponible comme accessoire en option.
Meilleur moment de la journée pour la prise
de vues
Le meilleur moment de la journée pour la prise de vues est entre 10 h et
14 h, lorsque le soleil est à la verticale.
Pour photographier dans des endroits mal éclairés par le soleil ou la nuit,
utilisez la torche de plongée sous-marine HVL-ML20M (en option).
En cas de problème
Symptôme
Présence de gouttes d’eau à
l’intérieur du Marine Pack.
Les fonctions
d’enregistrement et de lecture
n’ gissent pas.
Cause/Remèdes
• Les fermoirs sont mal verrouillés.
b Verrouillez correctement les fermoirs.
• Le joint torique n’est pas correctement en
place.
b Placez le joint torique uniformément dans
la gorge.
• Le joint torique est entaillé ou fendillé.
b Remplacez le joint torique par un neuf.
• La batterie est déchargée.
b Rechargez complètement la batterie.
• Le « Memory Stick Duo »/« Memory Stick
PRO Duo » est plein.
b Insérez un autre « Memory Stick Duo »/«
Memory Stick PRO Duo » ou effacez les
données inutiles du « Memory Stick Duo
»/« Memory Stick PRO Duo ».
• Le taquet d’interdiction en écriture du
« Memory Stick Duo »/« Memory Stick PRO
Duo » est sur LOCK.
b Placez le taquet sur la position
d’enregistrement ou insérez un « Memory
Stick Duo »/« Memory Stick PRO Duo »
neuf.
3
4
3
H
Power switch
Commutateur
d’alimentation
OPEN button
Touches OPEN
MENU button
Touche MENU
O-ring
Joint torique
1
2
1
Image Size/Delete
button
Touche Taille de
I’image/Suppression
Enter/Control button
Validation/
Touche de commande
 
 (flash)button/Control button
Touche 
 (flash)/Touche de commande
 (macro)button
/Control button
Touche 
 (macro)/
Touche de commande
 (review)button
/Control button
Touche 
 (revue)/
Touche de commande
 Self-timer/Control button
 Retardateur/Touche de commande
2
3
Spécifications
Matière
Plastique (PC, ABS), acier inoxydable, verre
Étanchéité à l’eau
Joint torique, fermoir
Résistance à la pression
Jusqu’à une profondeur de 40 m (132 pieds) sous l’eau
Commutateurs pouvant être commandés de l’extérieur
Alimentation, Mode, Déclencheur, Zoom, Flash, Macro, Commande,
Retardateur, Revue, Menu, Taille de l’image/Suppression
Dimensions
135 
×
 96 
×
 55 mm (5 3/8 
×
 3 7/8 
×
 2 1/4 po.) (l/h/p) environ
(parties saillantes et commandes non comprises)
Poids
280 g (9.8 on.) environ (Marine Pack seulement)
Accessoires fournis
Courroie de mein (1)
Graisse (1)
Joint torique (1)
Extracteur de joint torique (1)
Entretoise (1)
Mode d’emploi (1)
Manual d’entretien du joint torique (1)
Accessoires en option
Filtre couleur VF-MPTH
Kit de bras VCT-MP1K
Torche de plongée HVL-ML20M (doit être utilisée avec le kit de bras
VCT-MP1K, la batterie « InfoLITHIUM » (série M) et le chargeur de batterie
série M)
La conception et les caractéristiques sont susceptibles d’être modifiées sans
préavis.
2
MENU button
Touche MENU
Owner’s Record
The model and serial numbers are located inside of the unit.
Record the serial number in the space provided below.
Refer to them whenever you call upon your Sony dealer regarding this
product.
Model No.  MPK-THA
    Serial No.
Printed on 100% recycled paper using
VOC (Volatile Organic Compound)-free
vegetable oil based ink.
1
2
1
W
T
2
1
2
1
A
C
Hook for hand strap
Crochet pour
courroie de mein
Tripod mounting hole
When using a tripod, use a tripod with 5.5 mm
or shorter screws. This equipment cannot be
firmly fastened on a tripod with long screws.
Doing so might damage this equipment.
Filetage pour trépied
Utilisez un trépied dont la vis mesure 5,5 mm
de long ou moins. Cet équipement ne peut pas
se fixer solidement sur un trépied à vis longue.
Celle-ci pourrait aussi l’endommager
Control buttons
Touches de
commande
Image Size/Delete button
Touche Taille de I’image
Suppression
Zoom buttons (Index
buttons during
playback)
Touches de zoom
(Touches d’indexation
pendant la lecture)
Drip-proof packing
Garniture pare-gouttes
2
1
2
1
1