Sony MZ-R910 User Manual
18
Connecting to a stereo
system (LINE OUT)
system (LINE OUT)
See the illustration in English text 45.
Connect the i/LINE OUT jack of the recorder
to the LINE IN jacks of an amplifier or a tape
recorder with a line cable (RK-G129 or RK-
G136, not supplied).
The output is analog. The recorder plays the
MD digitally and sends analog signals to the
connected equipment.
to the LINE IN jacks of an amplifier or a tape
recorder with a line cable (RK-G129 or RK-
G136, not supplied).
The output is analog. The recorder plays the
MD digitally and sends analog signals to the
connected equipment.
When connecting a line cable to
the
the
i
/LINE OUT jack
When connecting a line cable (not supplied), be
sure to set the “AUDIO OUT” parameter for the
i
sure to set the “AUDIO OUT” parameter for the
i
/LINE OUT jack.
1
Press the jog dial.
2
Turn the dial until “AUDIO OUT”
flashes in the display, and then press to
enter.
flashes in the display, and then press to
enter.
3
Turn the dial until “LINE OUT” flashes
in the display, and then press to enter.
in the display, and then press to enter.
Notes
•
•
If the “AUDIO OUT” parameter for the i/
LINE OUT jack is set to “LINE OUT”,
VOLUME +/– or Digital Sound Preset will
not function.
LINE OUT jack is set to “LINE OUT”,
VOLUME +/– or Digital Sound Preset will
not function.
•
The “AUDIO OUT” parameter for the i/
LINE OUT jack cannot be set to “LINE OUT”
when the supplied remote control is
connected.
LINE OUT jack cannot be set to “LINE OUT”
when the supplied remote control is
connected.
•
When you connect the headphones/earphones
directly to the recorder, set the “AUDIO
OUT” parameter for the i/LINE OUT jack to
“HeadPhone”.
directly to the recorder, set the “AUDIO
OUT” parameter for the i/LINE OUT jack to
“HeadPhone”.
B Editing recorded tracks
You can edit your recordings by adding/erasing
track marks or labeling tracks and discs.
Premastered MDs cannot be edited.
track marks or labeling tracks and discs.
Premastered MDs cannot be edited.
Notes on editing
•
•
You cannot edit tracks on an MD that is record
-protected. Before editing tracks, close the tab
on the side of the MD.
-protected. Before editing tracks, close the tab
on the side of the MD.
•
If you perform an editing operation while
playing, editing results will not be recorded
until you stop the recorder and “TOC Edit”
disappears in the display.
playing, editing results will not be recorded
until you stop the recorder and “TOC Edit”
disappears in the display.
•
Do not move or jog the recorder while “TOC
Edit”* is flashing in the display.
Edit”* is flashing in the display.
•
The lid does not open until “TOC Edit”
disappears in the display after editing.
disappears in the display after editing.
•
When the group mode is on, editing can be
performed only for the tracks registered into
the selected group.
performed only for the tracks registered into
the selected group.
* TOC = Table of Contents
Labeling/relabeling
recordings
recordings
See the illustrations in English text (pages 46 to
49).
49).
You can name tracks, groups and discs using
the recorder’s character palette.
the recorder’s character palette.
Available characters
•
Capital and small letters of the English
alphabet.
alphabet.
•
Numbers 0 to 9
•
! " # $ % & ( ) * . ; < = > ? @ _ `
+ – ' , / : _(space)
+ – ' , / : _(space)
Numbers of characters you can
input
input
Track, group, or disc name: Approx. 200 each
(all available characters are mixed).
(all available characters are mixed).
Numbers of characters you can
input in a disc
input in a disc
Alphanumeric characters/symbols only
Approx. 120 titles of about 10 characters each
(a maximum of about 1,700 letters)
Approx. 120 titles of about 10 characters each
(a maximum of about 1,700 letters)
The number of titles that can be stored on a disc
depends on the number of characters that are
input for track names, group names, and disc
name.
depends on the number of characters that are
input for track names, group names, and disc
name.