Sony RM-V210 User Manual

RM-V210  3-276-523-11 (1) US/ES

RM-V210  3-276-523-11 (1) US/ES

RM-V210  3-276-523-11 (1) US/ES

RM-V210  3-276-523-11 (1) US/ES

RM-V210  3-276-523-11 (1) US/ES

Slide open the battery compartment and insert two size AA (R6)
batteries (not supplied).
Be sure to line up the + and – on the batteries with the + and – on the
battery compartment.

Under normal conditions, batteries will last up to one year. If the
Commander does not operate properly, the batteries might be worn
out.  Replace the batteries with new ones.

• Replace both batteries with new ones.
• Do not take more than 3 minutes to replace the batteries; otherwise,

your setting of the code numbers will be erased.

• Do not mix old batteries with new ones or mix different types of

batteries together.

• If the electrolyte inside the battery should leak, wipe the

contaminated area of the battery compartment with a cloth and
replace the old batteries with new ones. To prevent the electrolyte
from leaking, remove the batteries when you plan not to use the
Commander for a long period of time.

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.  This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference  to radio communications.  However, there is
no guarantee that interference will not occur in a particular
installation.  If this equipment  does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.

The Commander is preset at the factory to operate Sony brand
components.
If you’re using  the Commander with a Sony component, you won’t
need to preset the Commander before you start using it.
To set up the Commander to use with other (non-Sony)
manufacturers’ components, or to use with a component that is not
preset at the factory, you’ll need to follow the instructions in this
manual to preset the Commander with the correct code number for
your components. (See the supplied “Component Code Numbers”
also).

• The Commander can be set up to operate only one component per

button – unless their code numbers happen to be the same.  For
example, you cannot set up the Commander to operate a Sony TV
and a Panasonic TV simultaneously (because they use different
code numbers).

• You may not be able to operate even a Sony brand component with

the factory presetting. In such a case, follow the procedure in
“Setting the Code.”

Follow the steps 1 and 2 below for each component you plan to use
with the Commander.

1 See the supplied “Component code

numbers”, and find the four-digit code
number for the desired component.
If more than one code number is listed, use
the number that’s listed first.
For example, if you’re setting up a Sony
TV, you would use the code number 8201.
If your component isn’t listed, see
“Searching for the Correct Code.”

2 Press SET more than two

seconds.
The SET indicator lights up.

3 Press the button of the

component that you want to
set up.
The SET indicator lights up.

4 Press the Number buttons to enter the four-digit

component code number.

5  Press ENTER. The SET indicator turns off. If the SET

indicator flashes five times before lighting up, it
means that the setup is incomplete. Confirm the
component code number and start over from Step 4.

If you do not input anything into the Commander within 20 seconds
between each step, or if you press SET while setting the component
code, the setup procedure will be canceled.
Start over from Step 2.

1 Power on the component you want to set up.

2 Aim the Remote Commander at the component and press a button

to check if that button works.
For example, press the POWER button to see if it works on your
component .

3 Check that the other buttons of the Commander is operating the

corresponding functions of the component.

You can write down the code number on the label inside the
battery compartment lid.

If the Commander Doesn’t Seem to Be Working...
• First, try repeating these setup procedures using the other codes

listed for your component (see the supplied “Component Code
Numbers”).

• If – after trying all the codes listed for your component – you still

cannot get the Commander to work properly, try the search
method described in “Searching for the Correct Code.”

You can find a code number available for a
component that doesn’t have one in the
supplied “Component code numbers.”

Before starting the Search function
Set each component to the following status so
that the Search function works effectively.
TV, DVD Home Theater: Power-on
Other components: Power-off

* If any of these components are assigned to any

of the Component Select buttons, you can set a
component code using the Search function.

1 Press SET more than two seconds. The SET indicator lights up.

2 Press the Component Select button for the desired component.

The SET indicator lights up.

3 Press CH + or CH – and POWER in turn until the component

reacts as follows:

TV, DVD Home Theater: Powers off
Other components: Powers on

Press CH + to go to the next code number.
Press CH – to go back to the previous code number.
The SET indicator flashes once after the numbers have turned one
cycle.
One cycle means, for example, that the commander finishes
searching all the component code numbers allocated to the
component.

4 Press ENTER.

The SET indicator and the Component button turn off.
If the SET indicator flashes five times before turning off, it means
that the setup is incomplete. Start over from Step 3.

If the component does not operate properly, repeat steps 1 to 4 and
search for another code.

If you still cannot get the Commander to work properly, see
“Troubleshooting.”

1 Press the button of the desired component on the Commander.

TV

VCR

CBL

DVD

2 Point the Commander directly at the component.

3 Press the button for the function you want to use.

See “Remote Button Descriptions” for complete descriptions of the
buttons on the Commander.

Basically, use this Commander in the same way as the Commanders
supplied with your components.
• Using this Commander will not increase the functions of your

components. The functions of the Commander are limited to the
functions of the components themselves. For example, if your TV
does not have a MUTING function, MUTING on this Commander
will not function with your TV.

• Some functions of the component may not work with this

Commander.

• If your cable box can control volume, be sure to set its volume

switch to a medium position. If the volume on the cable box is
turned down completely, you will not be able to adjust your TV’s
volume with the Commander.

3-276-523-11(1)

Remote Commander

© 2007  

 

Sony Corporation     

Printed in China

2 To change the input mode.
3 and qd

Number buttons : To set items
selected from the screen.

4 To select numbers 10 and

above.

8 To show the current play status

on the screen.

9 To bring up the Master Guide.
q; To return to the previous

screen.

qd To enter the setting. To set

items selected from the screen.

qf To switch the subtitle.
qg

CH+: Channel up.
CH–: Channel down.

qh To select a deck.
qj To switch the subtitle.
qk To display the DVD menu.

Approx. 7 m (23 ft) (varies depending of the
component of each manufacturer)

Two size AA (R6) batteries (not supplied)

Approx. 1 year (varies depending on frequency of
button use - up to approx. 300 times per day.)

Approx. 53 

×

 220 

×

 29 mm (w/h/d)

(2 

1

/

8

 

×

 8 

3

/

4

 

×

 1 

3

/

16

 in.)

Approx. 108 g (3.8 oz.) (not including batteries)

Design and specifications are subject to change without notice.

The validity of the CE marking is restricted to only those countries
where it is legally enforced, mainly in the countries EEA (European
Economic Area).

If you have problems setting up or using the Commander:
• When setting up the Commander, carefully go through the procedures

described in “Setting the Code.”  If the code that’s listed first for your
component doesn’t work, try all the codes for your component - in the order
in which they’re listed.  If all the codes fail to work (or if your component is
not listed in this manual), try using the procedures in “Searching for the
Correct Code.”

• Check that you’re aiming the Commander directly at the component, and that

there are no obstructions between the Commander and the component.

• Make sure the batteries you’re using are not worn out, and that they’re

inserted correctly.

• Check that the button of the TV, VCR, CBL, or DVD is pressed to choose your

desired component.

• Check that the component has infrared remote capability.  For example, if

your component didn’t come with a remote commander, it probably isn’t
capable of being controlled by a remote commander.

• Should any problem persist, reset the Commander to the factory setting by

pressing the POWER, INPUT and VOL– buttons simultaneously.

If – after you’ve read through this manual – you still cannot get the
Remote Commander to work properly, call the Sony Customer
Support Helpline at 1-800-822-2217.

2 To change the input mode.
3, 4 and qd

To change the channel. For
example, to change to channel
5, press 0 and 5 (or press 5 and
ENTER).

8 To display the current channel

on TV.

9 To bring up Master Guide.
q; To exit the menu.
qf To operate the Picture-in-

Picture function.

qg

CH+: Channel up.
CH–: Channel down.

qh To operate JUMP, FLASHBACK

or CHANNEL RETURN function
on the TV.

qj To operate SLEEP function on

the TV.

qk To call up the MENU display.
ql To move the cursor upward,

downward, to the left, to the
right, or to enter the selection.

w; To call up the option menu.
wa To select TV input source.
ws A: VIDEO 1

B: VIDEO 2
C: VIDEO 3
D: VIDEO 4
.

: VIDEO 5

 :

VIDEO 6

 :

VIDEO 7

>

:

VIDEO 8

m

:     HDMI select

N

:

HDMI 1

M

:

HDMI 2

z

REC: Component video

connection select

x

:

Component video
connection 1

X

:

Component video
connection 2

wg To use the “FAVORITE”

function.

ql To move the cursor upward,

downward, to the left, to the
right, or to enter the selection.

w; To call up the “TOOLS” menu.
wa N:

To play.

m

:

To rewind.

M

:

To fast-forward.

z

REC: To record, press N

while pressing zREC.

x

:

To stop.

X

:

To pause.

.

: To proceed to the

previous location.

>

:

To proceed to the next
location.

 :

To operate “ Flash –.”

 :

To operate “ Flash +.”

ws B: open/ close

D: To display the Top Menu.
A: To call up the setup menu.

wd PAGE+: To select DVD deck.

PAGE-: To select HDD deck.

wf To display the title menu.

2 To switch the output of the

digital satellite receiver to the
TV. (When you connect a TV
cable or antenna to the receiver,
the output switches between a
TV and SAT program.)

3, 4 and qd

To change the channel. For
example, to change to channel
5, press 0 and 5 (or press 5 and
ENTER).

8 To turn on the display.
9 To bring up the Master Guide.
q; To exit the mode.
qf To call up the DISH menu.
qg Channel up: +

Channel down: –

qh To tune to the last tuned

station.

qj To call up the PVR menu.
qk To call up the MENU display.
ql To move the cursor upward,

downward, to the left, to the
right, or to enter the selection.

w; To bring up the Station Index.

wa N:

To play.

m

:

To rewind.

M

:

To fast-forward.

z

REC: To record, press N

while pressing zREC.

x

:

To stop.

X

:

To pause.

.

: To proceed to the

previous location.

>

:

To proceed to the next
location.

 :

Replay

 :

Advance

ws A: RED button

B: GREEN button
C: YELLOW button
D: BLUE button

wd PAGE+: Page up.

PAGE-: Page down.

wf To call up the title of the

recorded program.

wg To use the “FAVORITE”

function.

SET

TV

VCR

CBL

DVD

POWER

A

B

C

D

1

2

3

4

5

6

7

8

9

VOL

CH

0

PIP

INPUT

SLEEP

INFO

PAGE

GUIDE

MENU

LIST

FAV

EXIT

TOOLS

RECALL

MUTING

ENTER

OK

2 To change the input mode.
8 To expose the on-screen

display.

qf To switch the antenna output.
qg

CH+: Channel up
CH–: Channel down

qh To select a deck.
wa N:

To play.

x

:

To stop.

m

:

To rewind.

M

:

To fast-forward.

z

REC: To record, press N

while pressing zREC.

X

:

To pause.

2  To change the input mode.
3 and qd

To change the channel.
For example, to change to
channel 5, press 0 and 5 (or,
press 5 and ENTER).

8 To turn on the display.
9 To bring up Master Guide.
q; To clear the setting.

To exit the setting menu.

qg

CH+: Channel up .

(*PAGE+) Page up.

CH–: Channel down.

(*PAGE–) Page down.

qh To operate JUMP or

qj To call up “Tivo” menu.
qk To call up the MENU display.
ql To move the cursor upward,

downward, to the left, to the
right or to enter the selection.

wa N:

To play.

m

:

To rewind.

M

:

To fast-forward.

z

REC: To record, press N

while pressing zREC.

x

:

To stop.

X

:

To pause.

.

: To proceed to the

previous location.

>

:

To proceed to the next
location.

 :

To operate “ Flash –.”

 :

To operate “ Flash +.”

ws  D: (*Live TV)

To bring up Master Guide.
A: (*REPLAY)
To replay.
Or to go into REC/REVIEW
mode during play. (After about
5-second rewind, replay
begins.)

wd PAGE+ : (*THUMBS+)

To select the desired recorded
program.
(It is necessary to have
recorded the desired program.)
PAGE– : (*THUMBS–)
To select the desired recorded
program.
(It is necessary to have
recorded the desired program.)

wf  (*LIST)

To call up the title of the
recorded program.

* This key corresponds to Tivo service or the replay service. Refer to its

instruction manual for details.

2  To change the input mode.
3, 4 and qd

To change the channel
(for example, to change to
channel 5, press 0 and 5, or
press 5 and ENTER).

8 To turn on the display.
9 To switch the EPG display to

on/off.

q; To exit the setting menu.
qg

CH+: Channel up.
CH–: Channel down.

qh To toggle the current /previous

channel.

qk To call up the MENU display.
ql To move the cursor upward,

downward, to the left, to the
right, or to enter the selection.

wa N:

To play.

m

:

To rewind.

M

:

To fast-forward.

z

REC: To record, press N

while pressing zREC.

x

:

To stop.

X

:

To pause.

.

: To proceed to the

previous location.

>

:

To proceed to the next
location.

ws A: To operate “A” button.

B: To operate “B” button.
C: To operate “C” button.

wd PAGE+: Page up.

PAGE-: Page down.

wf To call up the title of the

recorded program.

wg To use the “FAVORITE”

function.

The following tables show brand names and their corresponding code numbers.

Las tablas que se presentan a continuación muestran las marcas y los números de código
correspondientes.

2 To change the input mode.
3 and qd

Number buttons: To set items
selected on the screen.

4 To select numbers 10 and

above.

6

VOL+: AMP volume up
VOL–: AMP volume down

7 AMP volume muting
8 To show the current play status

on the screen.

9 To change the sound.
q; To return to the previous

screen.

qf To switch the subtitle.
qg

CH+: Tuner +
CH–: Tuner –

qk To call up the MENU.
ql To move the cursor upward,

downward, to the left, to the
right, or to enter the selection.

w; AMP menu

wa N:

To play.

m

:

To rewind.

M

:

To fast-forward.

z

REC: To record, press N

while pressing zREC.

x

:

To stop.

X

:

To pause.

.

: To proceed to the

previous location.

>

:

To proceed to the next
location.

 :

To operate “ Flash –.”

 :

To operate “ Flash +.”

ws B: open/ close

A: To call up the setup menu.
C: Disc skip
D: To display the Top Menu.

wg To call up MEMORY.

ENTER

1 To set up the Commander,

press SET more than two
seconds.

6 Volume up: +

Volume down: –

7 To mute the volume on a TV

or a DVD Home Theater.

qa To turn on and off the power

of the selected component.

qs Component select buttons.

Press to select a component to
operate.

About tactile dots
The number 5 button, the N button and CH+ each have a tactile dot for
convenient use.

Note on the VOL+/- and MUTING buttons
The Commander controls or mutes the TV’s volume when you select a visual
component. The Commander outputs the signals to control or to mute a TV or
DVD Home Theater’s own volume when you have set one of these
components.

Notes
• There may be cases you may turn on/off the cable box by pressing CH+ or

CH– on the Commander.

• If your cable box can control volume, be sure to set its volume control to a

medium position.  If the volume on the cable box is turned down completely,
you will not be able to adjust your TV’s volume with the Commander.

SET indicator

SET

TV

VCR

CBL

DVD

POWER

1

2

3

4

5

6

7

8

9

VOL

CH

0

PIP

INPUT

SLEEP

INFO

RECALL

MUTING

ENTER

SET

SET

TV

VCR

CBL

DVD

POWER

1

2

3

4

5

6

7

8

9

VOL

CH

0

PIP

INPUT

SLEEP

INFO

RECALL

MUTING

ENTER

SET

TV

VCR

CBL

DVD

SET

SET

c

c

ENTER

TV

VCR

CBL

DVD

c

Sony
Bose
Insignia
JVC
LG
Nexxtech
Onkyo
Panasonic
Sharp
Yamaha
Zenith

4501, 4502, 4503, 4504, 4505
4512
4515
4507
4514, 4516
4515
4509
4506
4510
4511
4513

Sony

3001,3011,3012

—

—

DirecTV

3013, 3017, 3018,

—

—

3019, 3023, 3024

Dish Network

—

3010, 3014, 3025

—

General Electric

3019

—

—

Hitachi

3005

—

—

Hughes

3004

—

—

Humax

3402

—

—

JVC

—

3010, 3014

—

Magnavox

3018

—

—

Panasonic

3003

—

—

Philips

3018

—

—

Proscan

3002, 3007, 3019

—

—

RCA

3002, 3007, 3019,

—

—

3021

Samsung

3017, 3022

—

3404

Sylvania

—

—

3403

Toshiba

3006

—

—

Usdigital

—

—

3401

Sony

3101

ABC

9405

Adelphia

3107, 3110

Advanced Newhouse

3107

Altrio

3107

Americast

3105

Atlantic Broadband

3107

Bell South

3105

Blue Ridge

3107

Brigth House

3107

Cablevision

3107

Charter

3107

Comcast

3107

Cox

3107

General Instrument

3103, 9002, 9003, 9004, 9005, 9006, 9007, 9008, 9018,

9022, 9043, 9044

Gnc

3105

Hamlin

9022, 9023, 9024, 9025, 9026

Illico

3107

Jerrold

3103, 9002, 9003, 9004, 9005, 9006, 9007, 9008, 9018,

9022, 9043, 9044

Memorex

3106

Motorola

3103, 3110, 3111

NET

9042

Oak

9027, 9028, 9029

Pace

3107

Panasonic

9019, 9020, 9021

Paragon

3106

Philips

3104

Pioneer

3107, 9014, 9015

Pulsar

3106

Regal

9022, 9023, 9024, 9025, 9026

Rodgers

3107

Runco

3106

Scientific Atlanta

3102, 3107, 3108, 3109, 9009, 9010, 9045, 9046

Seren

3107

Sigecom

3107

Susquehanna

3107

Time Warner

3107

Tocom

9016, 9017, 9043

Toshiba

3106

Videotron

3107

Wideopenwest

3105, 3107

Zenith

3105, 3106, 9013

Sony

0201, 0202, 0203, 0024, 0030, 0211

Advent

0048

Aiwa

0015

Apex

0047

Broksonic

0214

Cyber Home

0034, 0035, 0226

Daewoo

0029

Denon

0002, 0017, 0205

Emerson

0040, 0228

Funai

0220

GO VIDEO

0042, 0212, 0233

Gpx

0046, 0049

Humax

0232

ILO

0227, 0230

Insignia

0042, 0215

JVC

0007, 0208

Kenwood

0050, 0051

LG

0218

Magnavox

0225

Marantz

0012

Panasonic

0205, 0213, 0002

Philips

0012, 0221, 0231

Pioneer

0004, 0019, 0021, 0204

Samsung

0014, 0212, 0229

Sansui

0214

Sharp

0219

Sylvania

0215, 0220

Symphonic

0040, 0041

Terapin

0036

Toshiba

0209

Yamaha

0205

Zenith

0218

Sony

3201, 3205, 3206

—

Humax

3202, 0413

—

Panasonic

—

3203

Philips

3202, 0412

—

Pioneer

0413

—

ReplayTV

—

3203, 3204

Tivo

3201, 3202

—

Toshiba

0413

—

TV

VCR/Cable box/Digital satellite
receiver/DVD/TV/Digital video
recorder/DVD Home Theater

Sony TV

Sony VHS VCR

Sony Cable box

Sony DVD player